Wrought iron
Wood & steel frame
Farm & ranch
Sliding driveway gates
LiftMaster operatorsFree on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Get your free estimateTrusted Gate Installation for Summerlin Homeowners
A gate that won’t open on a school morning or drags across the driveway slab usually isn’t a mystery. In Summerlin the cause is often visible before we pick up a tool: a warped redwood swing leaf that swelled through monsoon season, a track full of desert grit, or a masonry pier that settled out of plumb years ago and the old hinge can no longer hide. Our technicians, with up to 12 years of hands-on experience across driveway, pedestrian, and security gates, measure the opening, confirm the gate swing or slide path is clear, and test the automation before we recommend replacement. Same-day scheduling is available in Summerlin for installation assessments. Call (844) 797-2809 to start.
What Our Gate Installation Service Includes
Every gate installation we perform in Summerlin is scoped to the actual opening on your property, not a catalog size. Below are the six gate types we install and the specific work each one involves.
Driveway Gate Installation
A driveway gate is the full-width entrance gate for vehicles, usually automated and tied into the home’s power and access system. You need one when you’re replacing an aging leaf that no longer squares up, opening a new driveway approach, or upgrading from a manual gate to a powered one. We measure the opening, verify the driveway grade stays level through the swing or slide path, confirm the post footings will hold the leaf weight, and set the stop positions before handing over a written photo record of the finished install.

Pedestrian Gate Installation
A pedestrian gate is the walk-through gate set beside the driveway, at a side yard, or off a courtyard, sized for foot traffic and often left manual. You need one when a side-yard gate has rusted its hinges or a new walkway needs a matching entry point. We hang the leaf to clear the ground through the full swing arc, set a self-closing spring only where the property asks for it, and confirm the latch lines up with the strike post on the first try, not after three return trips.

Sliding Gate Installation
A sliding gate rolls or cantilevers along a track parallel to the fence line, which is useful when a driveway curves or doesn’t have room for a swing leaf. You need one when your driveway approach is tight against the house or the street, or when the property line doesn’t allow a swing. We check the track ground-bearing capacity, confirm the rollers sit at the same height across the full run, and set the end-of-travel limits so the gate stops where it should every time.

Swing Gate Installation
A swing gate pivots on a hinge post, either swinging inward toward the house or outward toward the street depending on the grade and code path of travel. You need one when the driveway layout points to a swing and there’s room for the leaf to clear the vehicle path. We verify the hinge post is set plumb, check the leaf clears the ground through the full arc, and confirm the open position holds without the leaf drooping over months of use.
Double Gate Installation
A double gate is a pair of leaves that meet at the center, most common on wide driveway approaches and on decorative entryways. You need one when a single leaf would be too heavy for the hinge or too wide to swing clear. We set both hinge posts to the same height, align the two leaves so they meet at the center without rubbing, and install the drop rod or center latch so the pair locks as one.
Security Gate Installation
A security gate is a heavier-duty gate, often steel tube or wrought-iron frame, installed where the property needs a physical barrier that also looks right. You need one when an older aluminum gate is too light for the wind load off the open desert edge, or a new property line needs a real closed boundary. We check the footing depth against the leaf weight, set the anchor pattern into concrete, and confirm the hinges carry the load evenly across the frame.
Styles & brands we work with
- Wrought iron
- Wood & steel frame
- Farm & ranch
- Sliding driveway gates
- LiftMaster operators
Brands We Service for Gate Installation

We install and service nine major gate-automation and hardware brands, so if the motor or hardware is already part of the job, we work with what’s there rather than steering toward a replacement motor. LiftMaster is the one we see on most Summerlin driveway gates, and we’re familiar with how the operator’s soft-start and reverse-sensor behave when the arc calibration slips. Mighty Mule is common on side-yard and pedestrian gates, and we know where the control board sits when a tenant in a neighboring property needs the swing direction changed. FAAC and BFT we see more often on heavier swing and sliding gates, and we know which of their limit switches typically drift after a hard summer.
DoorKing, Linear, Viking, Ghost Controls, and Elite round out the list. Every one of them has its own quirks around how the limits get set, how the safety edges are wired in, and what the operator expects from the power feed. Whether you have a LiftMaster, a Mighty Mule, a FAAC, or any other make on the property, we can help. That applies whether we’re installing a new gate or replacing the operator on the one you already have.
Before
AfterSigns You Need Gate Installation Right Now
Gates rarely fail on a convenient morning. These are the symptoms that most often mean the gate is past repair and due for replacement.
- The leaf is out of square and no hinge adjustment will fix it. A gate that was once plumb and has settled into a permanent diagonal drag is telling you the frame has warped or the hinge posts have shifted. Rehanging the leaf on a warped frame just moves the problem a few inches down the driveway.
- The bottom of the gate scrapes the driveway or the track. Scraping means the leaf has dropped on its hinges or the track has filled with sand and grit. Left alone, that scrape will chew through the gate’s finish and start biting into the concrete.
- The operator keeps losing its open and close limits. When a gate stops deciding where “open” should be, the motor’s limit switches are set wrong or the gate is drifting against a mechanical stop. That’s a sign the gate or the operator needs rework, not another reset.
- Rust has reached the frame joints, not just the surface. Surface rust on a gate is cosmetic. Rust at the welds or through the wall of a steel frame is structural, and the gate will eventually sag under its own weight.
- You’ve hit the third repair in two years. Three visits for the same failing part usually means the gate itself has worn past the point where repair makes sense. That’s when a written install estimate costs less than another round of repairs.
Our Gate Installation Process – Step by Step

- 1
Site assessment and written scope. We measure the opening, check the swing or slide path for clearance, confirm the driveway grade, and note where the power feed and control wiring will land. Before anyone picks up a tool, you get a written price under Haven Standard Clause 1 (“Have it in writing”).
- 2
Footing and post layout. We mark the hinge post or track line against the actual opening, confirm the anchor points clear any buried irrigation or low-voltage lighting, and set the footing depth to the gate weight and wind load. The photo record starts here.
- 3
Hinge, track, and leaf installation. The leaf is hung, the track is leveled across the full run, and the hinges are set so the gate clears the ground through the whole arc. We check the leaf sits plumb to within a fraction of an inch before the operator goes on.
- 4
Operator, accessories, and safety edges. The motor is mounted, the limit switches are set to the new open and close positions, and the photo-eye (the infrared beam that stops the gate if something crosses the path) is aligned and tested. If an access-control keypad or remote is on the job, we confirm the wiring diagram before we button up the control box.
- 5
Full test and written handoff. We open and close the gate through a full cycle several times, test the reverse sensor, and photograph the finished install. You get a written record of what was installed, the part numbers, and the settings before we leave. Under Haven Standard Clause 4 (“Evidence on every job”), that photo record is included at no additional charge.
See the difference
Before
After
Before
After
Before
AfterHow Much Does Gate Installation Cost in Summerlin?
A typical driveway gate installation in Summerlin runs $2,200 – $5,800 depending on leaf material, width, and whether the site needs new footing concrete. A pedestrian gate installation runs $900 – $2,400, and a security gate on a heavier steel frame runs $2,800 – $6,500. Sliding gate installation usually lands between $2,500 – $6,200, and a double gate runs $3,000 – $7,000 for the pair. Operator and automation work is priced separately, so the motor is not baked into the gate number.
What pushes a Summerlin install toward the top of a range: concrete footings on a sloped approach, a power run out to the gate line, and heavier leaf materials that need a crane or a two-person lift. A few things keep the number down: existing footings that pass a load check, a driveway approach already graded and level, and a gate line that clears buried irrigation without rerouting. We confirm each of these on site before the written price is issued.
What’s included in the free estimate: the written scope, the written price, and the line items that drive it (leaf, hinges, footings, operator if applicable). Nothing gets added to the invoice after the job starts. If a footing fails mid-install and requires extra concrete, we stop, write a revised scope, and get your sign-off before continuing.
Gate Installation Near Summerlin – Our Service Area

We install gates throughout Summerlin and the surrounding valley, including Spring Valley, Enterprise, Las Vegas, and Winchester. If you’re in an adjacent neighborhood, common response windows for an installation assessment are next business day unless you’re already on the schedule for a same-day visit. See our gate services overview for the full list of services, or jump straight to Gate Installation in Spring Valley if you’re on that side of the 215.
Serving Summerlin, NV – Our Local Coverage Area
We serve Summerlin and nearby communities. Use the map below to see the area we cover. If you’re nearby, we can almost certainly help.
Frequently Asked Questions – Gate Installation in Summerlin

Gate installation is the full job of putting a new gate on your property: fitting the leaf, setting the hinge post or track, hanging the hardware, and, where needed, wiring in the operator and safety edges. It’s different from gate repair, which reworks an existing gate. A typical Summerlin installation includes the written scope, the footings, the hinge or track hardware, and a full test cycle before we leave. If you’re not sure whether your gate needs installation or repair, call us and we’ll tell you which one you’re looking at.
A pedestrian gate is usually half a day, and a driveway swing gate runs most of a day once footing and operator work is counted. Sliding and double gates can stretch to two days if the footing has to cure before the leaf goes on. Security gates on heavier steel frames sit at the long end of that range. We schedule with the footing cure in mind so the gate isn’t hung on concrete that hasn’t set. Call (844) 797-2809 for a scheduling window that fits your property.
Pedestrian gate installation runs $900 – $2,400, driveway gates run $2,200 – $5,800, and security gates on steel frames run $2,800 – $6,500. Sliding and double gate installations land between $2,500 and $7,000 depending on width and hardware. The flat written price is handed over before any work starts, so the number on the invoice matches the number on the quote. Call (844) 797-2809 for an estimate – it’s free.
Yes, we install and service LiftMaster operators, and we work on eight other brands including Mighty Mule, FAAC, BFT, DoorKing, Linear, Viking, Ghost Controls, and Elite. That matters because if your existing motor is on the property and still working, we don’t force a replacement. We test it, check the limit-switch readings, and tell you whether it can carry a new gate. Call (844) 797-2809 with your motor model and we’ll confirm on the phone.
Same-day installation assessments are often available; the install itself is a scheduled job once the written scope is agreed. A gate has to be measured, ordered to size, and in many cases has to sit on cured footings, so the work is measured and scheduled rather than dispatched. What we can do same day is respond to an emergency (a gate stuck open, a security gate down) so the property isn’t left exposed. Call (844) 797-2809 and we’ll tell you what’s possible today.
The 365-Day Done Right Promise covers every completed install and repair for a full year: if the work isn’t right, we make it right with no argument and no fee. There’s no expiration on the obligation within that window. That promise holds on gate installations the same way it does on repair work. Call (844) 797-2809 if you have a warranty question on an existing install.
Clear the driveway or gate line the day before, and make sure we can reach the footing area without moving a car. If there’s an existing motor or access-control keypad wired in, let us know the model before we arrive so we can confirm the wiring diagram in advance. If you’ve had a written estimate from another company, bring the paperwork and we’ll review it at no cost under our free second-opinion policy. Call (844) 797-2809 to confirm the appointment.
Schedule Your Gate Installation Service in Summerlin Today
Whether you’re replacing a warped redwood leaf in The Ridges or hanging a new pedestrian gate off a side yard in Red Rock, we’d like to see the opening before we quote it. You’ll get a written scope, a written price, and a photo record when the work is done. Call Vance Gate Repair Summerlin at (844) 797-2809 for a free estimate. A live person answers 24/7.
Related services we also handle: Gate Installation in Las Vegas, gate repair, gate motor & opener service, gate access control, and gate parts & welding.
Written by the team at Vance Gate Repair Summerlin.