Wrought iron
Wood & steel frame
Farm & ranch
Sliding driveway gates
LiftMaster operatorsFree on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Get your free estimateStyles & brands we work with
- Wrought iron
- Wood & steel frame
- Farm & ranch
- Sliding driveway gates
- LiftMaster operators
See the difference
Before
After
Before
After
Before
AfterHow Much Does Gate Repair Cost in Summerlin?
Gate repair in Summerlin typically runs $175 to $650, with most single-visit fixes landing between $210 and $380. A limit-switch reset or hinge adjustment sits at the low end near $175 to $240, while a swing-gate motor replacement with new arms and brackets pushes past $550. Anything involving gate welding or full post repair moves higher.
Those numbers assume a residential driveway or courtyard gate within a Summerlin community. The range is wide because “gate repair” covers a stuck latch and a dead circuit board under the same three words. What stays constant is the process: we inspect, write the price, hand it to you, and only start work once you say yes. Our technicians have up to 12 years of experience on gates across the valley.
Key Takeaways
- Most Summerlin gate repair visits cost $210 to $380.
- Switches, hinges, and latches are usually $175 to $340.
- Motor and opener repairs run $285 to $650.
- Welding and post work is the biggest variable at $340 to $900+.
- A written price comes before any work starts, and every visit includes a photo record of what we found and what we set.
Gate Repair Cost Breakdown (2026)

The table below reflects what we see on Summerlin gates in 2026. These are starting ranges, not promises about your specific gate. When we inspect, the number gets narrowed fast, usually in under 20 minutes.
| Repair Type | Typical Cost | What’s Included |
|---|---|---|
| Service call with full inspection | $85 – $145 | On-site diagnosis, written scope, photo record |
| Limit-switch reset or travel adjustment | $175 – $240 | Reset arm travel, photograph new position |
| Hinge replacement (per hinge, double gates) | $95 – $160 | Weld-out, weld-in, realignment, latch test |
| Latch and striker adjustment | $145 – $220 | Latch realignment, gap correction, grease |
| Swing-gate motor replacement | $540 – $900 | Motor, arms, brackets, wiring check, new photo log |
| Sliding-gate opener repair (chain, gear, rack) | $285 – $580 | Chain tensioner, limit switch, gear set as needed |
| Photo-eye (safety beam) replacement | $195 – $310 | New sensor pair, alignment test, wiring diagram |
| Control board replacement | $290 – $540 | Board, wire transfer, labeled diagram left behind |
| Battery backup replacement | $230 – $380 | Battery, voltage test, photo of install |
| Gate welding / post repair | $340 – $900+ | Structural weld, rust treatment, repaint touch-up |
| Track straightening (sliding gates) | $390 – $720 | Anchors, track level, roller realignment |
Three things push a gate repair from the low end to the high end. Brand is the first. A LiftMaster or Elite board runs more than a Mighty Mule board, and the labor on a FAAC swing arm is different from labor on a BFT. Condition is second. A gate that has been dragging on its hinges for two Summerlin summers usually has a bent arm, a worn roller, and sometimes a fatigued post that needs welding. What the last person did is the third. We regularly open a control box and find a repair from three years ago with no diagram and a jumper wire that goes nowhere. Rebuilding that is more work than starting clean.
Before
AfterWhat Affects Gate Repair Pricing in Summerlin
- Which brand already lives on the gate. We service nine major automation brands: LiftMaster, FAAC, BFT, Linear, Viking, Ghost Controls, DoorKing, Elite, and Mighty Mule. If a gate has a brand on it, we can work on it. Nobody gets steered toward a new motor because we don’t happen to like the old one.
- Gate material and post condition. A wrought-iron swing gate in The Ridges absorbs heat and holds torque differently than a lighter aluminum sliding gate in Red Rock Country Club. Iron gates that get afternoon sun off the Spring Mountains want stiffer hinges and thicker welds, which adds $60 to $150 to a hinge job.
- Whether the gate is on a slope. Plenty of Summerlin driveways sit on a pitch. A gate that closes uphill needs a different arm setting and a stronger operator, and that arm costs more than a flat-lot equivalent.
- Access to the control box and power. If the operator is mounted low behind landscaping, we spend extra time clearing access before we can read the board. Boxes mounted in full sun with no shade are also more likely to have heat-damaged control boards, and those get replaced, not repaired.
- How many things failed at once. One hinge is a small job. Four hinges, a dragging latch, and a photo-eye that got knocked off by a landscaper is a bigger one. We price each item separately and you approve the whole scope in writing before we start.
- Whether you have a photo record from the last technician. Under Clause 4 (Evidence on every job) we leave a photographic record of every adjustment at no extra charge. If you have that record from a prior visit, our inspect step is faster. If you don’t, we rebuild the diagram from scratch, and that adds time.
How to Save on Gate Repair

Gate repair isn’t the place to chase the lowest quote. An undertightened hinge fails in a season, and then you pay twice. That said, there are real ways to save on a gate repair in Summerlin.
- Fix the small stuff before it becomes structural. A dragging latch that costs $145 to adjust today becomes a bent post and a $700 weld job next spring. The single best way to save on gate work is to fix the noise before the gate stops moving.
- Get a second opinion on any written estimate. We offer a free second opinion on any written estimate from another company. Bring the paperwork, and we’ll review it at no cost. If the estimate names a repair your gate doesn’t need, you have a right to know.
- Ask for the flat price in writing before work starts. Our pricing is written and handed over before any tool comes out of the bag, which is how Haven Standard Clause 1 (“Have it in writing”) works on every single visit. A verbal estimate is not a price. It’s a conversation.
- Keep a paper trail. Save the photo log and diagram from every visit. When a repair goes wrong, the record is the difference between a small fix and a full reinstall. We also back every job with the 365-Day Done Right Promise: if it’s not right, we make it right, no fee, no argument.
- Don’t put off the annual check. A gate that gets a yearly look in Summerlin usually spends $0 beyond the service call. A gate that waits until it fails is a $500 repair. Call (844) 797-2809 for a free estimate – estimates are free and the price is written.
What Typically Breaks on a Summerlin Gate?
Summerlin’s climate does specific damage. Low humidity cracks hinges and dries out the grease in a swing arm faster than in coastal markets. Summer afternoons cross 100 degrees and the black metal on an iron gate gets hot enough to distort a cheap photo-eye bracket. Desert wind pushes dust into the track of a sliding gate, and that dust grinds against the rollers. We see those failures on nearly every visit.
The pattern is predictable. In a Summerlin community like Summerlin West or The Paseos, windblown sand gathers on sliding-gate tracks, rollers wear unevenly, and the gate starts to lean. On the iron-side communities like The Ridges and Red Rock Country Club, hinge fatigue drives most of our calls, and hinges on those gates are welded, not bolted. That changes the price. A bolted hinge runs $95 to $160. A welded hinge pulls the price toward the upper end because the old weld has to come out clean before a new one goes in.
Auto-closers go out on a schedule too. Mechanically the inside of the operator is fine; the battery in the backup dies around the three-year mark. A dead battery is a $230 to $380 replacement, not a $600 motor job, and every service call includes a voltage test on the backup so you know it’s coming. We leave a photo of the meter reading with the invoice.
Repair or Replace: Which Costs Less?

Repair almost always costs less. A $400 motor repair beats a $1,400 replacement 9 times out of 10, and a hinge job that costs $300 keeps a gate alive for years. Replacement starts to make sense when the gate structure itself is compromised: a bent post, a rotted stile, a track anchor pulling out of concrete. Those are welding and structural jobs, and if you have three of them at once, we’ll tell you plainly that replacement may be the smarter spend. That’s the only time we say it.
We do not steer toward replacement. If the motor on your gate can be fixed, we fix it. That’s the whole approach. Our technicians have up to 12 years of experience working on whatever motor already sits on the property.
How the Repair Process Works
- Call for a free estimate. A live person answers 24/7 at (844) 797-2809. No voicemail loop, no callback window, no automated attendant. You’ll be given a time and the name of the technician coming out.
- On-site inspection. We photograph the gate, the operator, and the control box. We test the limit switches, read the board, and check every hinge, roller, and latch. Typical inspection is 15 to 20 minutes.
- Written price before work. You get a written scope and a written price. You approve before any tool comes out of the bag. This is Haven Standard Clause 1, and it applies to a $175 switch reset the same as a $900 motor replacement.
- Repair and documentation. When we finish, we leave a photo record of what we found, what we adjusted, what we replaced, and the part numbers. Under Clause 4, that record comes with every visit at no extra charge.
- Follow-up and the 365-Day Done Right Promise. If the repair isn’t right, we make it right within one full year of the original job, at no additional charge. No argument, no re-inspection fee.
Safety First: What We Won’t Ask You to Do

Gate motors pull, and a 400-pound swing gate under power doesn’t stop for a hand. We don’t ask homeowners to test photo-eyes by walking the beam, reset a limit switch themselves, or reach into an opener’s control box. High-tension springs on swing gates and 120-volt wiring at the operator are the two spots where a do-it-yourself approach goes badly. That work belongs to a trained, background-checked technician who has tested the safe edges and documented the travel. If your gate is dead or won’t stop, don’t force it. Call (844) 797-2809 and let a professional look at it.
Brands We Service in Summerlin
We work on the automation brand that’s already on your gate: LiftMaster, FAAC, BFT, Linear, Viking, Ghost Controls, DoorKing, Elite, and Mighty Mule. That means we don’t have to tell you “we only service X.” We show up with the right diagnostic for your specific operator, whether it’s a LiftMaster board or a Mighty Mule arm.
Nearby Cities We Also Serve
If your property sits just outside Summerlin, we also serve the neighboring communities. You can see the full service scope on our home page. We handle residential and light commercial gates across the valley, including gate installation on new builds.
FAQs – Gate Repair Cost

How much does gate repair cost in Summerlin?
Most gate repairs in Summerlin cost $175 to $650, with the typical single-visit job landing between $210 and $380. Small fixes like a limit-switch reset or a latch adjustment sit near $175 to $240. Motor repairs and board replacement push toward the upper end. Call (844) 797-2809 for an exact quote – estimates are free and the price is written before work starts.
Can you come out the same day?
Same-day scheduling is often available in Summerlin, and a live person answers the phone 24/7 at (844) 797-2809. If we can get to you today, we will. If we can’t, you’ll get a real time slot, not a callback window. The technician’s name and photo are provided before arrival.
Is it cheaper to repair my gate or replace it?
Repair is almost always cheaper. A $540 motor job beats a $1,400 gate replacement nine times out of ten, and the 365-Day Done Right Promise backs the repair for a full year. Replacement makes sense when the gate structure itself is compromised by a bent post or rotted stile, and even then, welding often costs less than starting over. Call (844) 797-2809 for a written comparison.
Why is my gate motor clicking but not moving?
A motor that clicks but doesn’t move is usually a dead limit switch, a loose chain, or a burned control board, and the fix ranges from $175 to $540 depending on which one it is. On a summer day in Summerlin, heat-damaged boards are a common cause. Call (844) 797-2809 for an inspection and a written price before any work starts.
Do you offer a guarantee on gate repair?
Yes. Every completed repair is covered by the 365-Day Done Right Promise: if the repair isn’t right within one full year, we make it right at no additional charge. That’s in addition to the written price and photo record you receive on every visit. Call (844) 797-2809 to schedule.
What documents do I get when the job is done?
You get a photo record of what we found, what we adjusted, and what we installed, plus part numbers and a wiring diagram if we touched the control box. Under Haven Standard Clause 4, that record comes with every visit at no additional charge. It’s the same documentation habit we carried over from commercial access-control work.
Contact Vance Gate Repair Summerlin
If your gate is stuck, dragging, or making a sound it didn’t make last month, call us at (844) 797-2809 for a free estimate. A live person answers 24 hours a day, seven days a week. Our technicians have up to 12 years of experience, and every job comes with a written price before work starts, a photo record when we leave, and the 365-Day Done Right Promise behind it. We service residential and light commercial gates across Summerlin and the surrounding valley, working on whatever automation brand your gate already has. No “call for a quote” – the price is on paper before a single tool comes out.
Pricing reflects the Summerlin market as of 2026. Vance Gate Repair Summerlin offers free estimates – call (844) 797-2809.
What Our Customers Say
"Our gate was hit by a delivery truck. They came out, documented the damage properly for the insurer, and the claim went through without an argument."
- Camille R."Honest about what did not need doing. Told me the operator had years left and only the control board needed replacing."
- Douglas N."Good work on a long driveway gate. Arrived when they said, finished when they said."
- Sofia E.