Wrought iron
Wood & steel frame
Farm & ranch
Sliding driveway gates
LiftMaster operatorsFree on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Get your free estimateStyles & brands we work with
- Wrought iron
- Wood & steel frame
- Farm & ranch
- Sliding driveway gates
- LiftMaster operators
See the difference
Before
After
Before
After
Before
AfterHinge & Post Repair in Summerlin, NV
Hinge and post repair in Summerlin typically costs $145 to $420 per hinge or post, depending on whether the post is reset in existing concrete or fully re-poured, and whether the gate is a pedestrian walk gate or a heavier driveway swing gate. Most hinge repairs are completed in a single visit, and most post resets take two visits because the concrete needs to cure before the gate goes back on. We do the work under a written price you hold in your hand before we pick up a tool, and we leave a photo record of every adjustment.
Summerlin’s housing stock spans roughly three decades, and that matters for hinges. The original 1990s villages (The Trails, The Crossing, Las Ventas) sit on expansive clay soils that swell and shrink with irrigation cycles. We see gate posts there lean two to four degrees over a decade, which racks the hinge and wears the barrel pin unevenly. Newer builds in Redpoint and Summerlin West tend to fail differently: treated pine posts dried out and split around the lag bolts within five to seven years. Same symptom, different cause. Call (844) 797-2809 and a live person answers, day or night.
This page covers the hinge and post side of a broader category. For motors, photo-eyes, limit switches, and access control, start with our Gate Repair in Summerlin page or the main Gate Repair hub. Our technicians have up to 12 years of experience, and every one of them arrives background-checked and uniformed, with a name and photo sent before they reach the driveway.
Key Takeaways
- Hinge repair runs $145 to $320; post reset or replacement runs $250 to $420.
- Most hinge work is same-visit; post resets need a cure window, usually 24 to 48 hours.
- We photograph and document every adjustment, then leave the log with you.
- All completed work carries the 365-Day Done Right Promise.
When You Need Hinge & Post Repair
- The gate sags and drags on the ground. A sagging gate usually means a hinge barrel has worn oval, or the top hinge plate has pulled its screws out of soft wood. In Summerlin’s Redpoint and Reverence, we regularly see spring failures on the same gates where the lower hinge is loose, because the extra load fatigues both parts together.
- The post is leaning or visibly out of plumb. A post that has rotated more than about two degrees will not hold a hinge adjustment. We see this most in older villages on irrigated lots where the soil under the footing stays wetter than the builder planned. A level gate hung on a leaning post will sag again within a season.
- The gate won’t latch or clear the strike post. If the gate has shifted laterally by a half inch or more, the latch and the strike no longer line up. That is a post or hinge-plate problem, not a latch problem, and replacing the latch alone wastes money.
- You hear a metal-on-metal screech when the gate swings. Dry barrel hinges, or a hinge pin worn on one side, produce a grinding sound that grease will quiet for a week and then not fix. This is the cheapest hinge problem we see and the one most likely to turn into a bent post frame if it’s ignored.
- Visible rust staining or loose bolts on a steel gate. Ornamental steel gates in Summerlin’s west-side neighborhoods see fine dust that traps moisture against the hinge plate. Rust bleed at the weld line is a hinge failure in progress.
- The gate wobbles when you push it. Play at the top of the gate, side to side, is the signature of a hinge pin that has worn past tolerance or a post footing that has cracked loose from the surrounding concrete.
Our Hinge & Post Repair Process

- Photograph and document what we found. Before any adjustment, we photograph the hinge clearances, the post plumb with a digital level, and the footing where it meets concrete. That record goes into the job file.
- Diagnose the cause, not just the symptom. We check whether the hinge is worn, whether the post has moved, or whether both have failed. A hinge replaced on a moving post will fail again; we tell you that up front so you don’t pay twice.
- Write the scope and price, and hand it to you. You get the parts named, the labor named, and the total named on paper before we start. Under Haven Standard Clause 1, there is no “call for a quote” and no invoice surprise at the end.
- Repair or reset. For hinges, we remove the worn barrel, confirm the leaf plate is sound, and install a matched replacement with the correct pin and clearance. For posts, we either reset the existing post in a reinforced footing or set a new galvanized or steel post to the same height and hinge geometry. If the gate is automated, we check the arm alignment with the motor afterward, and we can service the motor across LiftMaster, FAAC, BFT, Mighty Mule, and five other automation brands rather than pushing you toward a replacement gate.
- Test, adjust, and leave the record. We swing the gate, check latch alignment, verify clearances, and confirm any automation still runs its full travel. Before we leave, you receive the photo log of every adjustment and the written part numbers installed.
Before
AfterHinge & Post Repair Pricing in Summerlin
These are the ranges we quote most often on Summerlin gates. The written price on your job is what you pay; these numbers tell you roughly where you’ll land before you call.
| Item | Typical price range | Notes |
|---|---|---|
| Single hinge replacement (steel or wood gate) | $145 – $240 | Includes removal, new hinge, and alignment |
| Two hinges paired (top and bottom) | $260 – $380 | Common when one hinge wears and loads the other |
| Hinge plate re-secured (loose lag bolts, soft wood) | $160 – $290 | May include steel backing plate or through-bolt upgrade |
| Post reset in existing footing | $250 – $340 | Requires a cure window before rehanging the gate |
| Post replacement with new footing | $320 – $420 | Galvanized or steel post, new concrete, new hinge mount |
| Gate rehang after post work | $120 – $180 | Alignment and latch reset included |
What pushes a quote toward the top of the range: a gate on a slope, where plumb and swing plane both need correction; ornamental steel where hinges are welded rather than bolted, which adds setup time; or a post footing set in a hardpan layer that requires a cutting bit. What keeps it low: a single worn hinge on a pedestrian walk gate with sound wood and an accessible bolt pattern.
Before we arrive, we tell you what the price will be. If you have a written estimate from another gate company in Summerlin and want it looked at, we’ll review it at no charge. That’s the free second opinion, and it’s on the house. For the rest of the service picture, including motors and access control, see our home page or the Gate Repair overview.
How long does the repair take?
Hinge replacement is typically same-visit, in and out inside one to two hours. Post resets are usually two visits: one to set and level the post, then a return after the concrete cures (about 24 to 48 hours in Summerlin’s summer heat) to rehang the gate and finish the alignment.
What else affects hinge and post cost?
Automated gates add a step. When the gate has a motor, we realign the arm and confirm the limit switches after the hinge or post work. This is where nine-brand coverage matters: whether the property runs a LiftMaster, FAAC, BFT, Linear, Viking, Ghost Controls, DoorKing, Elite, or Mighty Mule motor, we can pick up the existing setup and get it back to spec rather than quoting a new operator just to make a hinge fix stick.
FAQs – Hinge & Post Repair

How much does a gate hinge replacement cost in Summerlin?
Gate hinge replacement in Summerlin typically costs $145 to $240 for a single hinge, and $260 to $380 when the top and bottom hinges are replaced together. A welded hinge on ornamental steel runs higher because the weld has to be cut and redone. Call (844) 797-2809 for an exact written price, and estimates are always free.
Can you fix a leaning gate post without replacing it?
Often yes. If the post is sound and the footing is intact, we can reset and plumb it rather than replace it, which keeps the cost closer to $250 to $340 instead of a full replacement. We rope the gate, lift the post, correct the base, and set it into a reinforced footing. If the post is split, rusted through at the base, or the concrete has fully failed, replacement is the honest answer, and we’ll tell you so before starting.
Is it cheaper to repair the hinge or replace the gate?
Repair is almost always cheaper. Hinge and post work runs a few hundred dollars, while a replacement driveway gate in Summerlin can run well into four figures once fabrication, hardware, and rehanging are added. We repair the hinge and post unless the gate frame itself is compromised, and we’ll photograph what we see so you can make that call with the evidence in hand.
Do you service automated gates when you fix the hinge?
Yes. We realign the operator arm and re-verify the limit switches and photo-eye after any hinge or post work. If the gate is on a FAAC or BFT operator, or a Mighty Mule on a lighter swing gate, we know the travel and clearance tolerances for each. Call (844) 797-2809 for a free estimate on the hinge and post work plus a check of the motor.
If a post is leaning, a hinge is grinding, or the gate has started to drag, call (844) 797-2809 for a free estimate. A live person answers 24 hours a day. We’ll photograph what we find, write the price on paper before we pick up a tool, and back the repair with the 365-Day Done Right Promise. Our technicians have up to 12 years of experience, and every visit ends with a documented record you keep.
Written by the team at Vance Gate Repair Summerlin, serving Summerlin.