Wrought iron
Wood & steel frame
Farm & ranch
Sliding driveway gates
LiftMaster operatorsFree on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Get your free estimateStyles & brands we work with
- Wrought iron
- Wood & steel frame
- Farm & ranch
- Sliding driveway gates
- LiftMaster operators
See the difference
Before
After
Before
After
Before
AfterWhat Electric Gate Repair Costs in Summerlin, NV (and Why the First Quote Is Usually Too Low)
Electric gate repair in Summerlin typically runs $285 to $650 for a straightforward board or operator fix, and $950 to $2,400 when the buried low-voltage wire run has to be diagnosed and replaced alongside it. Those two numbers are far apart for a reason, and the gap is the whole story behind most underquoted gate repairs here. If you want the real number on your gate rather than a phone guess, call (844) 797-2809. We put the price in writing before anyone touches a tool.
Here’s the pattern we keep seeing. A gate stops working. A company replaces the control board, the gate runs for two or three weeks, then quits again. The homeowner calls us for a second opinion holding the first invoice, and the paperwork shows the board was swapped but nobody tested the wire in the ground. The board was a symptom. The failing part was a corroded junction twelve inches under the driveway.
Why the Same Gate Breaks Twice in Summerlin
An electric gate is two systems wearing one coat of paint. There’s the mechanical side (motor, operator arm, hinges, rollers, track) and the electrical side (transformer, control board, low-voltage wire run, photo-eye sensors, limit switches). They fail in ways that look identical from the driver’s seat. The gate doesn’t move. You can’t tell which system let go until somebody puts a meter on it.
Summerlin makes the electrical side fail more than most places. The caliche-laden soil and expansive clay that sit under a lot of these lots move with the seasons, and that movement cracks the conduit and nicks the buried low-voltage wire. Mineral-heavy groundwater gets in. The copper corrodes. The connection gets weak, resistance climbs, and the voltage at the motor drops below what the board can tolerate. The board works harder to compensate, heats up, and eventually dies. Put in a fresh board without finding the corroded junction and you’ve just fed a $400 part to a bad wire run. Three weeks later it’s dead again.
That’s how a $300 repair becomes a $1,100 one. The homeowner pays twice because the first visit treated the electrical failure as a mechanical job.
What our meter readings catch before the new board goes in
We take voltage readings at three points on every electric gate call: at the transformer, at the board, and at the far end of the wire run at the motor. If the number at the motor is meaningfully lower than the number at the board, the drop is happening in the wire between them, which points to buried corrosion and not a bad board. Those readings get photographed and written into the job record. Under Clause 4 of The Haven Standard (Evidence on every job), that photo log is yours at no extra charge. It’s the same wiring-diagram habit we brought over from commercial access-control work, where a gate that fails an inspection because of an undocumented splice costs somebody a lot more than the splice did.
This is also why we service whatever motor is already on your gate. LiftMaster and FAAC operators are common on Summerlin driveway gates, and Mighty Mule shows up on lighter pedestrian gates, but the brand matters less than what the meter says. We’ve worked on enough of these that the brand doesn’t steer the diagnosis. The readings do.
What an Honest Electric Gate Repair Quote Itemizes

A low quote is usually low because it’s missing line items, not because somebody is being generous. Here’s what should appear on any written estimate for electric gate repair in Summerlin, and what the cheap version quietly leaves off.
| Line item | Typical cost range | What a low quote skips |
|---|---|---|
| Control board replacement | $285-$520 | Voltage checks before install |
| Wiring continuity test (buried run) | $95-$180 | Whole test, or runs it only at the surface |
| Transformer output test | $60-$120 | Assumes the transformer is fine |
| Buried low-voltage wire replacement | $380-$900 | Every bit of it |
| Photo-eye sensor alignment | $75-$150 | Leaves sensors off-axis |
| Limit-switch calibration | $70-$140 | Sets travel by feel |
| Full electrical + mechanical diagnostic | $95-$160 (often credited toward repair) | Usually the whole reason the quote is low |
Add the line items up and a proper full-system diagnosis plus repair lands around $950 to $2,000 depending on how much wire has to come up. Compare that to two separate visits where the second one has to re-diagnose everything the first one skipped. The full diagnostic is the cheaper path, even though its invoice is larger.
When you’re comparing quotes, ask any company three questions: Will you test voltage at the transformer, the board, and the motor end? Will you run a continuity test on the buried wire before replacing the board? And will I get a written scope and a photo record before you leave? If a quote doesn’t answer all three, the price isn’t comparable. It’s just lower.
Before
AfterThe HOA Layer That Changes What Counts as a Fix
Summerlin is HOA-governed almost everywhere, and that matters for electric gate work on shared community gates, pool gates, and recreation-area gates in a way it doesn’t on a private driveway. Common-area gates carry a low-voltage safety standard, and the photo-eye loop (the infrared beam that stops the gate if something crosses the path) is part of that safety system, not an accessory. A repair can get the gate opening and closing electrically and still fail an HOA inspection if the safety-loop integrity wasn’t restored, the sensors weren’t re-aligned to spec, or the limit switches were set so the gate doesn’t fully clear the loop before reversing.
On gated enclaves like The Ridges and Red Rock Country Club, gate repairs also have to match approved finish colors and swing or slide geometry. A re-hung gate that works perfectly but drifts from the approved design can get flagged. We document the existing geometry before we touch it so the re-hang matches what the architectural guidelines expect.
For private driveway gates on the 1990s-through-2010s stucco-and-tile homes across Summerlin’s planned villages, the physical conditions add their own wear. Desert sun bakes powder-coat finishes and dries out hinges, and monsoon dust storms blow gates out of alignment and snap operator arms. A gate that “just needs adjusting” often turns out to have a settled or heaving post footing on the fill-and-caliche ground underneath. Re-hanging a gate on a bad footing gets you a straight gate for one season.
How our process runs, start to finish
- Diagnostic with the meter, not the eye. Voltage at the transformer, at the board, and at the motor end, plus a continuity test on the buried run. All readings photographed.
- Separate the electrical from the mechanical. We confirm which system failed before we name a part.
- Written price handed over before any work. Flat scope, flat price. That’s Clause 1 of The Haven Standard (Have it in writing). No surprise invoice when the job wraps.
- Repair, then document. Photo log of what was found, adjusted, and replaced, plus the part number installed, left with you and filed in the record.
- 365-Day Done Right Promise. If something we repaired isn’t right within a year, we make it right at no charge.
That last one matters more on electrical gate work than anywhere else. If buried wire corrosion re-manifests within the year, we come back at no charge. Not because it’s a warranty talking point, but because the documentation from the first visit shows whether the failure is a new problem or the same one we already touched. That’s the whole reason we photograph the readings. It protects you and it keeps us honest.
We don’t invent license numbers or review counts to sound official. We’re licensed and insured, our technicians are background-checked and their name and photo come to you before they arrive (our technicians have up to 12 years of experience), and a live person answers the phone at any hour. No voicemail loop, no callback queue. For a closer look at everything we handle, see our Gate Repair service page, and for the broader picture of what we do across the community, our home page and Gate Repair in Summerlin overview.
FAQs

Electric gate repair in Summerlin runs $285 to $650 for a board, operator, or sensor fix, and $950 to $2,400 when the buried low-voltage wire run has to be replaced too. The wide range is real because the two systems fail in ways that look the same until you put a meter on them. Call (844) 797-2809 for an exact written quote – the diagnostic and the price come before any work starts.
A gate that stops working two or three weeks after a repair usually had its mechanical symptom fixed while the corroded wire junction that caused the electrical failure stayed in the ground. The new control board then gets fed the same low voltage that killed the old one. Ask any company to run a continuity test on the buried run and show you the voltage at the transformer, the board, and the motor before they replace a board. Call (844) 797-2809 and we’ll do exactly that.
Repair is almost always cheaper unless the gate frame or posts are structurally gone. A board and wire repair runs $950 to $2,400; a full automated gate replacement runs several times that. On Summerlin’s caliche and fill ground, a settled post footing can look like a “replace it” situation when it’s actually a re-set. Call (844) 797-2809 for a written comparison of both paths before you decide.
Same-day visits are usually possible, and a live person answers our line 24/7 – no voicemail, no callback window. The diagnostic runs $95 to $160 and is typically credited toward the repair. You get the written scope and price in hand before anyone touches a tool, plus a photo record when we leave. Call (844) 797-2809 for the soonest slot.
Get the Price in Writing Before Anyone Picks Up a Tool
If your electric gate in Summerlin is down, or it broke once already and you’re not sure the last repair was the real fix, bring us the first invoice and we’ll review it at no charge. You’ll get voltage readings, a written scope, a flat price, and a photo record of the whole thing. Free estimates, upfront pricing, and the 365-Day Done Right Promise behind every repair. Call (844) 797-2809 today.
Written by the team at Vance Gate Repair Summerlin.
What Our Customers Say
"Our gate was hit by a delivery truck. They came out, documented the damage properly for the insurer, and the claim went through without an argument."
- Camille R."Honest about what did not need doing. Told me the operator had years left and only the control board needed replacing."
- Douglas N."Good work on a long driveway gate. Arrived when they said, finished when they said."
- Sofia E.