A Vance company - serving Summerlin, NV

Ghost Controls Welding & Fabrication in Summerlin, NV

Wrought ironWrought iron
Wood & steel frameWood & steel frame
Farm & ranchFarm & ranch
Sliding driveway gatesSliding driveway gates
LiftMaster operatorsLiftMaster operators
Every visit starts with

Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted

The assessment is free and the quote is the invoice.

Get your free estimate

Ghost Controls Welding & Fabrication: The Summerlin Owner’s Guide

We repair and replace the welded steel components on Ghost Controls driveway gates in Summerlin, and most fabrication jobs land between $340 and $1,150 installed, depending on whether we’re re-welding an existing bracket or replacing a hinge post, arm mount, or gate frame section outright. Same-day service is available for weld repairs that don’t require a custom-fabricated part. Most Summerlin owners don’t discover a fabrication problem until the gate starts to sag, drag, or bind – the welds crack slowly, and the first sign is usually a gate that closes a half-inch lower than it used to. By the time the motor strains or a hinge rips loose, the crack has typically been growing behind the paint for months.

Call (844) 797-2809

Which Ghost Controls Models This Applies To

Ghost Controls builds primarily for the DIY and light-residential market – the TSS1, TDS2, and ARD series arms mount to gate frames using bolted brackets and welded steel hinge posts, and it’s those mounts and posts that fail earliest. The automation itself is rarely the problem. Before we quote anything, we identify the exact arm model from the label on the housing and measure the bracket spacing in inches, because Ghost Controls changed its mounting-plate footprint between production runs in the mid-2010s and aftermarket brackets that fit one series won’t line up on another. That measurement is the single most common compatibility gotcha on these gates.

On the OEM-versus-aftermarket question: Ghost Controls sells replacement brackets and arm hardware direct, but the gate-side fabrication – hinge posts, frame gussets, weld repairs – isn’t a factory part at all. It’s local steel work, and that’s where an independent fabricator matters. We’re not affiliated with Ghost Controls; we service their equipment and thousands of other gates, and we don’t steer you toward a new motor when the frame just needs welding. Ghost Controls is one of nine automation brands we work on, alongside LiftMaster, Mighty Mule, and DoorKing.

Explore

Styles & brands we work with

  • Wrought iron
  • Wood & steel frame
  • Farm & ranch
  • Sliding driveway gates
  • LiftMaster operators

Signs Your Ghost Controls Welding & Fabrication Is Failing

Technician performing professional gate hardware installation and repair
Signs Your Ghost Controls Welding & Fabrication Is Failing

Summerlin’s dry heat and intense UV load what most welds never see in milder climates. Here’s what we find:

  • A hairline crack at the hinge post weld. Thermal cycling expands and contracts the steel daily, and a weld that wasn’t fully penetrated from the start opens along that seam. This is the most common failure we see on Summerlin gates, and it’s easy to miss because the crack stays tight until it doesn’t.
  • The gate sags and drags on the ground. A cracked weld at the post or a bent hinge lets the gate drop. Once it drags, the Ghost Controls arm is fighting extra load it was never sized for, and the operator itself starts to fail within weeks.
  • The arm bracket is bent or wallowed out. If the bracket that anchors the Ghost Controls arm to the gate frame has elongated bolt holes or a bent flange, the arm swings out of alignment and the gate binds at the halfway point. This usually follows a hard wind event or someone leaning on the gate.
  • Rust bleeding through paint at a seam. Summerlin is dry, but irrigation runoff and morning condensation collect at weld seams, and rust starts inside the joint before you see it on the surface. Rust streaking under a weld is a warning, not a cosmetic issue.
  • The gate racks (twists) when it moves. A twisted frame means a weld has moved. Racking stresses the Ghost Controls arm and the hinges together, and it gets worse every cycle until something gives.
Before & after

See the difference

Before - Recent ProjectBeforeAfter - Recent ProjectAfter
Recent Project
Before - Full RestorationBeforeAfter - Full RestorationAfter
Full Restoration
Before - Complete UpgradeBeforeAfter - Complete UpgradeAfter
Complete Upgrade
BeforeBefore
AfterAfter

Replacement Cost & What’s Included

Here’s what fabrication work on a Ghost Controls gate runs in Summerlin. The price is written and handed to you before any tool comes out – no “call for a quote,” no invoice bigger than the number you agreed to.

Job Installed price range
Weld repair (re-weld a cracked hinge, bracket, or frame seam) $340 – $550
Replace a bent Ghost Controls arm bracket $400 – $680
Rebuild or replace a hinge post $650 – $1,150
Custom-fabricated gate-frame section or gusset $850 – $1,400

What drives the range is how much steel we’re replacing and whether the gate has to come off its hinges. Parts and labor are quoted separately so you can see both. Every completed fabrication job is covered by our 365-Day Done Right Promise – if the weld isn’t right, we make it right, no charge, no argument. Before we leave you get a photo log of the finished weld and the gate re-hung and cycled.

DIY or Call Us?

professional gate repair service
DIY or Call Us?

There’s a real split here, and it comes down to whether the job is inspection or structural welding. An owner can safely do the inspection side: look for cracks at the hinge post with a flashlight, check whether the gate drags or racks, and wipe a weld seam to see if rust is bleeding through. That tells you whether you have a problem worth a call.

The welding itself is where DIY goes wrong. Gate-frame steel carries the full weight and swing load of the gate and the Ghost Controls arm, and a weld that looks fine but isn’t fully penetrated will crack again in a few months – often mid-cycle, with the gate falling. Welding near a painted gate also risks heat damage and even fire from debris inside the frame. Tacking a bracket with a box-store welder is how a $400 repair becomes a $1,100 one. If the gate is cracked, bent, or dragging, call us at (844) 797-2809 for a free estimate and we’ll tell you honestly whether it’s a weld repair or something simpler.

Get the price in writing before anything starts.A real person answers, day or night.
Call now

FAQs

Need Gate Repair help nationwide? Licensed & insured · 1-hour response · free estimates
Call (844) 797-2809
Local Service Coverage

Request a Free Estimate in Summerlin

Tell us what you need - Vance Gate Repair Summerlin responds fast. No obligation.

By submitting this form you agree to our Privacy Policy and consent to be contacted by phone, email or SMS about your request, including by local professionals who may handle it.

Prefer to text? Text Us
Call Now - 24/7 Dispatch