Wrought iron
Wood & steel frame
Farm & ranch
Sliding driveway gates
LiftMaster operatorsFree on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Get your free estimateGhost Controls Hinge & Roller Replacement: The Summerlin Owner’s Guide
We replace failed Ghost Controls hinge and roller assemblies for Summerlin gate owners, and most jobs land between $185 and $340 installed, depending on whether the hinge is a single bolt-on pivot or a full top-and-bottom roller carriage. Same-day service is usually possible on parts-only repairs when you call in the morning, and every job gets a written price before we open a tool bag.
Owners usually discover this part is gone the same way. The gate starts to sag at the latch side, or it drags a groove into the driveway pavers, and then one afternoon the gate swings but won’t close flush. Some hear a squeal at the hinge about halfway through travel. Others just notice the gap at the latch has grown from an eighth of an inch to nearly half. In Summerlin, we see this part fail faster on west-facing driveways where the afternoon sun bakes the hinge casting and the grease cooks out of it.
Which Ghost Controls Models This Applies To
Ghost Controls builds its residential swing-gate operators around a handful of arm families, and the hinge and roller assembly you need depends on which one is on your gate, not which motor head is bolted to the post. The Heavy-Duty (HD) series, the Standard (ST) series, and the newer single-piece arm units each use a different pivot geometry and a different roller diameter. Before we order anything, we read the model sticker on the control box, measure the gate leaf width and post spacing, and photograph the existing hinge so the part we pull matches the one that came off.
Here’s the compatibility gotcha that costs owners a return shipment: a hinge that physically fits a Ghost Controls post plate is not automatically the right hinge for the swing arc. The pivot offset on the HD arms is roughly a quarter-inch different from the ST series, and using the wrong one throws your open and close limits off by several degrees. You’ll chase a phantom limit-switch problem for an hour and never find it, because the hinge is the culprit. We stock no parts and carry none on a truck, so we measure, order the correct Ghost Controls-compatible or quality aftermarket equivalent, and install it in one visit. Note that we’re an independent service provider, not affiliated with Ghost Controls.
Styles & brands we work with
- Wrought iron
- Wood & steel frame
- Farm & ranch
- Sliding driveway gates
- LiftMaster operators
Signs Your Ghost Controls Hinge & Roller Replacement Is Failing

- The gate sags at the latch side. A worn hinge bushing lets the leaf drop, and gravity does the rest. Once the top hinge has lost its bushing material, the bottom hinge carries load it was never designed for.
- The gate drags on the ground or pavers. A seized roller stops rolling and starts scraping. In Summerlin, fine desert dust works into the roller race and turns the grease into a grinding paste.
- A squeal or groan at the hinge during travel. The bearing surfaces have run dry. This is early-stage failure and the cheapest point to catch it, before the casting itself wears oval.
- The gate won’t close flush, or the latch misaligns. A hinge that has shifted its pivot offset changes the swing arc by a few degrees. Your Ghost Controls operator then fights the mechanical bind and may trip its obstruction sensor.
- Visible play when you rock the gate by hand. Lift the leaf slightly at the open edge. More than a small amount of vertical slop means the hinge pin or bushing is worn and replacement is due.
See the difference
Before
After
Before
After
Before
After
Before
AfterReplacement Cost & What’s Included
Installed pricing for this work in Summerlin runs $185 to $340 for a single hinge and roller set, and $340 to $520 when both top and bottom hinges need replacement plus a limit re-set. The range is driven by three things: the hinge type (HD versus ST geometry), whether the gate needs re-hanging to restore the swing arc, and how much re-alignment of the Ghost Controls arm is required afterward. We price parts and labor as one written number, so you know the total before we start.
Every job includes the new hinge and roller hardware, re-greasing with a heat-rated lubricant suited to Summerlin’s summer temperatures, a limit-switch re-set if the arm needed adjustment, and a photo record of what came off and what went on. The 365-Day Done Right Promise covers the work for a full year: if the hinge fails or the gate drifts out of alignment, we make it right at no charge.
DIY or Call Us?

You can safely check a few things yourself. Rock the gate by hand to feel for play at the hinge. Look for grease that has turned gritty or blackened. Check whether the gate closes flush and whether the latch gap has changed. Those checks confirm the diagnosis without any risk.
Where DIY goes wrong is the re-hanging itself. A gate leaf on a Ghost Controls arm can weigh 250 to 400 pounds, and once the hinge pin is out, that weight is uncontrolled. Homeowners have crushed fingers and dropped gates onto driveways trying to hold a leaf and thread a new hinge at the same time. The arm also needs its limits re-set after the hinge swap, and getting that wrong means the operator keeps driving the gate past travel and stressing a brand-new hinge. That part is a two-person job with the right blocking and a written re-set procedure. When you’re ready, call (844) 797-2809 and we’ll walk the symptom through with you before we commit to a visit.
FAQs
Expect eight to twelve years in most climates, but in Summerlin we regularly see five to seven on west-facing gates, because the hinge grease cooks out in the summer heat and the roller race fills with dust. Re-greasing twice a year with a heat-rated lubricant is the single biggest thing that stretches that lifespan. Call (844) 797-2809 for a look if your hinge is already past the five-year mark.
Sometimes, yes. A worn bushing or a dry pin can often be cleaned, re-greased, and put back in service, and we’ll tell you honestly when that’s the better call. Once the hinge casting itself is oval or the roller race is scored, replacement is the only fix that holds. We check both before recommending anything.
A single hinge and roller set takes about 45 to 90 minutes, and a full top-and-bottom job with arm re-alignment runs two to three hours. That includes the photo record and the limit re-set. We give you the time window in writing before we start.
We measure the existing hinge and roller, read the model sticker, and match the pivot offset and roller diameter to the correct series before ordering. We carry no parts on the truck, so the part is ordered to your exact spec and installed in one visit. Call us for a free estimate and we’ll confirm what your gate needs.
If your Ghost Controls gate is sagging, dragging, or won’t close flush, help is one call away. Our technicians have up to 12 years of experience with Ghost Controls, LiftMaster, Mighty Mule, DoorKing, and five other major brands. Every visit comes with a free written price, a documented photo record, and the 365-Day Done Right Promise. Call Vance Gate Repair Summerlin at (844) 797-2809 for a free estimate.
Written by the team at Vance Gate Repair Summerlin, serving Summerlin and nearby areas.