Wrought iron
Wood & steel frame
Farm & ranch
Sliding driveway gates
LiftMaster operatorsFree on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Get your free estimateDoorKing Gate Parts & Welding in Summerlin: What to Know First
We provide independent DoorKing gate parts and welding in Summerlin, and most hinge, roller, latch and rail repairs are completed in a single visit once the right part is on hand. Welded post and frame repairs usually run longer because the metal has to be cut, fitted and finished, not just bolted on. You get a written price before any work begins, so the number you agree to is the number you pay.
This page is for Summerlin homeowners with a DoorKing swing gate or slide gate who need a part replaced or a weld made, not a full system replacement. As an independent DoorKing service provider, we’re not affiliated with or authorized by DoorKing, but we know their equipment closely. Call (844) 797-2809 and a live person answers, day or night.
How DoorKing Products Fail – and How We Fix Them
DoorKing builds heavy, long-lived gate hardware, and the failures we see in Summerlin tend to cluster around a handful of known weak points. Here are the five we run into most, with the model lines where they show up and what we actually do about them.
- Hinge wear on 6400 and 6500 swing-gate arms. The pivot bushings on these arms take the full weight of a steel or ornamental gate, and after years of daily cycling they develop vertical play. You’ll notice the gate sagging at the latch side and dragging on the ground. We replace the worn bushings and, if the hinge plate has ovaled, weld in a reinforced replacement rather than just tightening what’s left.
- Post rot and footing cracks at the gate post. Summerlin’s soil shifts with our irrigation-heavy landscaping and the summer heat cycle, and a gate post that was set years ago can develop hairline cracks at the footing or lean slightly. A leaning post throws off every limit position on the operator. We assess the footing, straighten and re-weld the post where it’s sound, and tell you plainly when a post replacement is the honest call.
- Rail fatigue and weld separation on slide-gate frames. On heavier slide gates, the bottom rail takes repeated impact and the original welds can crack at the corner joints. You’ll hear a rattle or see the gate tracking unevenly. We cut out the failed weld, clean the metal to bare steel, and re-weld with a proper penetration pass, then touch up the finish so it doesn’t rust.
- Roller and track wear on slide gates. DoorKing slide operators ride on guide rollers, and flat-spotted or seized rollers make the gate bind and strain the motor. We replace the rollers and check the track for bends, because a new roller on a bent track just wears out again.
- Latch and lock misalignment after a gate settles. When a gate shifts even a quarter inch, the latch stops catching cleanly and the lock won’t seat. We realign the latch, adjust the strike, and confirm the operator’s limit switches still read true after the adjustment, which prevents the gate from straining against a closed latch.
Styles & brands we work with
- Wrought iron
- Wood & steel frame
- Farm & ranch
- Sliding driveway gates
- LiftMaster operators
Our DoorKing Gate Parts & Welding Process

Every DoorKing job follows the same sequence, and the documentation is part of the work, not an afterthought.
- 1
Diagnose on site. We test the operator, walk the gate through its full travel, and photograph what we find: the worn hinge, the cracked weld, the limit-switch reading.
- 2
Decide OEM versus aftermarket. Some DoorKing parts are worth the OEM replacement for fit and longevity; others have a quality aftermarket equivalent that costs less and performs the same. We tell you which is which and why.
- 3
Write the price. You get the flat price in writing, covering the part and the labor, before anyone picks up a tool. No “call for a quote,” no invoice surprise at the end.
- 4
Make the repair. Welds are cleaned to bare steel and finished; parts are fitted and torqued to spec.
- 5
Test and document. We cycle the gate, confirm the limits and safety devices, and photograph every adjustment and the part number installed.
- 6
Leave the record. You get a photo log of what was found and what was replaced, filed in the job record, covered by the 365-Day Done Right Promise.
See the difference
Before
After
Before
After
Before
After
Before
AfterWhat DoorKing Gate Parts & Welding Costs in Summerlin
These ranges reflect what common DoorKing gate parts and welding jobs run in the Summerlin market. Your written price is confirmed after we’ve seen the gate.
| Job | Typical range |
|---|---|
| Hinge or bushing replacement (per hinge) | $150 – $320 |
| Gate roller replacement (slide gate) | $180 – $350 |
| Latch and lock realignment | $120 – $260 |
| Rail repair or re-weld | $250 – $600 |
| Post straightening and re-weld | $300 – $750 |
| Custom welding / frame repair | $350 – $900 |
What moves the price: whether the part is OEM or aftermarket, whether the metal needs cutting and refinishing, and how much disassembly the repair requires. Estimates are free, and the price is always written and agreed before work starts.
Why Summerlin Homeowners Call Vance Gate Repair Summerlin for DoorKing Work

DoorKing equipment is unforgiving of guesswork, and that’s where the documentation habit pays off. Every visit leaves a photographed record of what we found, what we adjusted, and what we installed, so the next technician isn’t starting from scratch. That’s Clause 4 of The Haven Standard, and it’s included at no charge. Our technicians have up to 12 years of experience, and we service nine major gate-automation brands, including LiftMaster, Mighty Mule and Ghost Controls, so we can work on whatever motor is already on your property rather than pushing you toward a replacement. Every completed repair is covered by the 365-Day Done Right Promise. A live person answers the phone 24/7, and you’ll know your technician’s name before arrival. Call (844) 797-2809.
FAQs
Using quality aftermarket or OEM-equivalent parts won’t void a DoorKing warranty by itself, but the safest path is to ask us to match the part spec. We’ll tell you when an OEM part protects the warranty and when a quality aftermarket part is the smarter buy.
Most common DoorKing wear parts, including hinges, rollers and latches, are available through our parts sourcing, and many jobs are completed the same visit once the part is confirmed. Rarer or model-specific parts may need to be ordered, and we’ll give you a written timeline before you commit.
Repair is usually the right call when the operator and gate frame are structurally sound and only the hinge, roller, latch or weld has failed. We’ll tell you honestly when the frame is beyond a sound repair, but we don’t steer toward replacement when a repair will hold.
We handle parts and welding jobs on a scheduled basis, and we’ll give you a clear appointment window when you call. Call (844) 797-2809 for an exact quote, and estimates are free.
Most rail, hinge-plate and post welding is done on site with the gate supported and the operator isolated for safety. If a weld can’t be made safely in place, we’ll explain why and quote the removal and reinstall before starting.
Call (844) 797-2809 for a free estimate on your DoorKing gate parts or welding job in Summerlin. We’ll diagnose it, write the price, and leave you a documented record of the work.
Written by the team at Vance Gate Repair Summerlin, serving Summerlin and nearby areas.