A Vance company - serving Summerlin, NV

DoorKing Welding & Fabrication in Summerlin, NV

Wrought ironWrought iron
Wood & steel frameWood & steel frame
Farm & ranchFarm & ranch
Sliding driveway gatesSliding driveway gates
LiftMaster operatorsLiftMaster operators
Every visit starts with

Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted

The assessment is free and the quote is the invoice.

Get your free estimate

DoorKing Welding & Fabrication: The Summerlin Owner’s Guide

We weld and fabricate DoorKing-compatible gate frames, hinge brackets, and post-mount repairs in Summerlin, and most jobs run between $275 and $850 installed depending on whether we’re repairing a cracked bracket or rebuilding a galvanized frame section. Same-day service is available on most repair calls. Owners usually find this failure the hard way: the gate sags at the hinge side, the arm bracket pulls away from the post, or the gate starts dragging on the concrete and the motor begins straining. In Summerlin’s heat, the sun hits steel gate frames on the west side of a house for six to seven hours a day in July and August, and that expansion cycle is what cracks the welds at the hinge plate first. The motor keeps working. The structure behind it doesn’t.

Call (844) 797-2809

Which DoorKing Models This Applies To

DoorKing swing and slide operators are only as good as the steel they’re bolted to. The fabrication work covers the frame and mount side of the system, not the controller: hinge brackets, post plates, operator mounting plates, arm brackets, and slide-gate frame sections. Whether you have a Model 6400 swing operator, a 9000-series slide operator, or an older 6002 on a residential driveway, the steel mounting geometry is what fails and what we repair.

Identifying the right part starts with the operator label, usually inside the control box, which gives you the model and serial. From there we measure the hinge spacing, the post-to-gate gap, and the bracket bolt pattern. DoorKing brackets are specific in ways aftermarket copies often miss: the arm bracket bolt pattern and the offset on the operator mounting plate vary by series, and a generic bracket that “looks close” will put the arm out of alignment and wear the operator faster. For frame and bracket work we fabricate to the measured dimensions rather than chasing a discontinued DoorKing part number, which is usually faster and stronger than an OEM replacement that may be back-ordered. On parts that must match exactly, we source OEM through DoorKing’s parts channel or a verified equivalent, and we tell you in writing which route we’re taking before we start.

Explore

Styles & brands we work with

  • Wrought iron
  • Wood & steel frame
  • Farm & ranch
  • Sliding driveway gates
  • LiftMaster operators

Signs Your DoorKing Welding & Fabrication Is Failing

Technician performing professional gate hardware installation and repair
Signs Your DoorKing Welding & Fabrication Is Failing
  • Visible crack or rust bloom at a hinge weld. This is the classic first failure. Thermal cycling opens a hairline crack, moisture gets in, and the weld starts to rust from the inside. Early on it shows as a brown streak running down the frame from the hinge.
  • Gate sagging and dragging on the ground or concrete. A failing hinge bracket or post plate lets the gate drop a half-inch, which is enough to make it drag and overload the operator. The motor gets blamed; the bracket is usually the cause.
  • Arm bracket pulling away or gate flexing under motor push. When the operator mounting plate or arm bracket loses its weld, the gate flexes instead of swinging cleanly. You’ll hear it before you see it: a creak or pop each time the motor reverses.
  • Gate no longer latching true in the closed position. Frame distortion from a cracked weld throws the gate out of square, so the latch misses by an inch or two. The operator keeps running into the stop.
  • Operator straining or tripping its limit. When the structure flexes, the operator works against a moving target and can’t hit its limit switches cleanly. This is the structural problem showing up as an electrical symptom.
Before & after

See the difference

Before - Recent ProjectBeforeAfter - Recent ProjectAfter
Recent Project
Before - Full RestorationBeforeAfter - Full RestorationAfter
Full Restoration
Before - Complete UpgradeBeforeAfter - Complete UpgradeAfter
Complete Upgrade
BeforeBefore
AfterAfter

Replacement Cost & What’s Included

Installed welding and fabrication work in Summerlin runs roughly $275 to $850, and the price you get is written down before we touch the gate. Small bracket and weld repairs sit at the low end; a rebuilt frame section or a replaced post plate with re-hanging the gate sits at the high end. The range is driven by how much steel we replace, whether the gate has to come off the hinges, and whether the operator has to be re-aligned afterward.

What’s included: the onsite measurement, the fabrication, the welding, refinishing the new steel against rust, re-hanging and re-aligning the gate, and re-checking the operator’s limits so the gate runs clean. Every job carries our 365-Day Done Right Promise, and under Clause 4 every visit leaves a documented photo record of what we found, what we welded, and what we set.

DIY or Call Us?

professional gate repair service
DIY or Call Us?

You can safely check the gate by hand: push it through its swing and feel for flex, look for rust streaks at the hinge welds, and confirm the frame is square against the latch. That tells you whether the structure is the problem.

What we don’t recommend is welding it yourself. Structural welding on a gate frame that carries a DoorKing operator is not a hobby job: a weld that looks sound but isn’t fully penetrated will crack again within a season, and the frame can fail while the operator is pushing it. A gate that drops off a hinge in motion is a real injury risk, and hot work near the operator’s wiring and controls needs to be done with the power isolated. We’d rather you call and get it done once. Call (844) 797-2809 for a free estimate.

Get the price in writing before anything starts.A real person answers, day or night.
Call now

FAQs

Need Gate Repair help nationwide? Licensed & insured · 1-hour response · free estimates
Call (844) 797-2809
Local Service Coverage

Request a Free Estimate in Summerlin

Tell us what you need - Vance Gate Repair Summerlin responds fast. No obligation.

By submitting this form you agree to our Privacy Policy and consent to be contacted by phone, email or SMS about your request, including by local professionals who may handle it.

Prefer to text? Text Us
Call Now - 24/7 Dispatch