Wrought iron
Wood & steel frame
Farm & ranch
Sliding driveway gates
LiftMaster operatorsFree on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Get your free estimateDoorKing Hinge & Roller Replacement: The Summerlin Owner’s Guide
We replace failed DoorKing hinges and rollers on Summerlin swing and slide gates, and most single-hinge or roller swaps land between $145 and $290 installed depending on the model and whether the weld plate is sound. Same-day service is often possible when you call in the morning. Owners usually discover the problem the same way: the gate starts dragging at the latch side, the motor runs longer than it used to, or they hear a metal-on-metal grind as the gate swings past the halfway point. By then the roller has usually flat-spotted or the hinge pin has worn oval, and the opener is working harder to push a gate that no longer moves freely.
Which DoorKing Models This Applies To
DoorKing hinge and roller hardware shows up across their swing-gate and slide-gate lines, most commonly on the 6002, 6003, 6400 and 6500 series operators, and on the 9000 and 9100 slide-gate models. The part you need depends on the gate, not the operator: swing gates use pivot hinges and a guide roller, slide gates use carriage rollers and a track-mounted idler. To match correctly, we read the model plate on the operator housing, measure the gate leaf thickness and the hinge pin diameter (usually 5/8 inch or 3/4 inch on residential leaves), and photograph the existing hardware before ordering.
The OEM-versus-aftermarket call matters here. DoorKing’s factory hinge assemblies are built to a specific pin tolerance and bushing material, and a cheap aftermarket roller with a nylon bushing will flat-spot in the Summerlin heat within a season. We use OEM or a quality equivalent rated for the gate weight, and we tell you which one we’re installing and why. Vance Gate Repair Summerlin is an independent service provider and is not affiliated with DoorKing; we source compatible parts and stand behind the install. We service LiftMaster, Mighty Mule and Ghost Controls hardware the same way.
Styles & brands we work with
- Wrought iron
- Wood & steel frame
- Farm & ranch
- Sliding driveway gates
- LiftMaster operators
Signs Your DoorKing Hinge & Roller Replacement Is Failing

Most Summerlin gates fail at the hinge or roller before the operator does. Here’s what we look for, and what each symptom tells us:
- The gate sags at the latch side. A worn hinge pin or a collapsed bushing lets the leaf drop a quarter to a half inch, so the latch no longer meets the strike cleanly and the gate drags on the ground.
- Grinding or squealing during travel. A flat-spotted or seized roller skids along the track instead of rolling, and the noise gets worse as the gate moves through the arc.
- The operator strains or reverses mid-cycle. When a hinge binds, the opener’s force setting climbs until it hits the safety limit and reverses. Homeowners often blame the motor when the real fault is a $60 hinge.
- Visible play when you push the gate by hand. Grab the gate at the hinge and rock it side to side; more than about 1/8 inch of movement means the pin or bushing is worn out.
- Rust staining or cracked weld plates. Summerlin’s dry heat bakes out lubricant and monsoon-season humidity works on exposed steel, so hinge plates crack at the weld and rollers seize.
See the difference
Before
After
Before
After
Before
After
Before
AfterReplacement Cost & What’s Included
Installed pricing for Summerlin, quoted in writing before any work starts:
- Single hinge replacement (OEM or quality equivalent): $145 – $190 installed, including the part, labor and a photo record.
- Single roller replacement: $120 – $165 installed.
- Full hinge-and-roller set (both hinges plus guide roller): $290 – $475 installed, depending on model and weld-plate condition.
- Cracked or failed weld plate repair: $95 – $180 add-on, quoted separately because it changes the scope.
What drives the range: model, leaf weight, whether the existing weld plates are sound, and whether we’re replacing one part or the full set. The price you’re handed covers parts and labor; there’s no surprise line at the end. Completed work carries our 365-Day Done Right Promise, and every visit includes a photo log of what was replaced, at no extra charge.
DIY or Call Us?

You can safely check the obvious things yourself: push the gate by hand to feel for binding, rock it at the hinge to measure play, look for rust or cracked weld plates, and confirm the model number on the operator plate. What we don’t recommend is loosening a hinge bolt on a gate that’s still attached to an operator with stored spring tension, or trying to drive out a seized pin with the leaf hanging free. A heavy swing gate that drops suddenly can crush a hand or a foot, and a binding hinge that fails under motor force can swing the leaf past its stop.
The swap itself is usually 30 to 90 minutes on a standard residential leaf once the right part is in hand. If you’ve found play, grinding, or a gate that reverses mid-cycle, call us at (844) 797-2809 and we’ll confirm the model, quote the price in writing, and schedule the visit.
FAQs
How long should DoorKing hinges and rollers last? A quality OEM hinge or roller typically lasts 8 to 12 years under normal residential use, but Summerlin’s heat and dust cut that shorter on exposed gates. We regularly see rollers flat-spot at 5 to 7 years here, well before the hinge pin wears out. Call (844) 797-2809 for a free quote and we’ll tell you what’s left on yours.
Can a failing hinge or roller be repaired instead of replaced? Sometimes, yes. A binding hinge can often be cleaned, re-greased and re-pinned, and a roller can occasionally be freed and re-tracked rather than swapped. We check repairability first and quote the cheaper option when it will hold. Call (844) 797-2809 and we’ll give you an honest read.
How long does the hinge and roller swap take? A single hinge or roller runs 30 to 60 minutes; a full set on both leaves takes 60 to 90 minutes, plus any weld-plate repair. We schedule same-day when the part is in hand. Call (844) 797-2809 to confirm timing.
How do you source the replacement part? We read the model plate, measure the pin diameter and leaf thickness, and order OEM or a quality equivalent rated for the gate weight. We don’t guess at the size. Call (844) 797-2809 and we’ll quote the exact part before we order.
Written by the team at Vance Gate Repair Summerlin, serving Summerlin and nearby areas.