Wrought iron
Wood & steel frame
Farm & ranch
Sliding driveway gates
LiftMaster operatorsFree on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Get your free estimateGhost Controls Gate Motor Replacement: The Summerlin Owner’s Guide
We replace Ghost Controls gate motors across Summerlin, and most installed jobs land between $680 and $1,250 depending on which series you have and whether the arm bracket, control board, and battery harness are reusable. We keep same-day slots open for motors that have already quit, and every price is written and handed to you before a tool comes off the truck. Most Summerlin owners don’t discover the motor is the problem until the gate starts stopping halfway, the arm runs but the gate doesn’t move, or the operator beeps and gives up after one attempt.
Which Ghost Controls Models This Applies To
Ghost Controls builds its residential line around a handful of series, and the parts that fail are not interchangeable across them. The heavy-duty AX-series arms use a different motor and gearbox than the lighter TDS-series, and the HS-series slide operators are a different animal entirely. Before you order anything, find the model plate: it’s usually on the underside of the control box or stamped on the arm housing near the manual release. The plate gives you a model number and a manufacturing date, and the date matters because Ghost Controls has quietly revised arm castings and controller connectors over the years. A replacement arm from an older batch may not bolt to a newer bracket without an adapter.
The OEM-versus-aftermarket question for Ghost Controls is more nuanced than for LiftMaster or Mighty Mule, which we also service. Ghost Controls sells direct and its parts are reasonably accessible, but aftermarket motors and control boards do exist, and some are good while others are not. Our rule: OEM motor and gearbox unless the OEM part is unavailable or has a known flaw in your series, in which case we’ll name the aftermarket equivalent on the written quote so you can see exactly what’s going on your gate. Nothing gets ordered until you’ve agreed to the part number.
Styles & brands we work with
- Wrought iron
- Wood & steel frame
- Farm & ranch
- Sliding driveway gates
- LiftMaster operators
Signs Your Ghost Controls Gate Motor Replacement Is Failing

- Arm runs but the gate doesn’t move. The motor is spinning but the gearbox or the arm’s internal clutch has stripped. On Ghost Controls arms, this usually shows up as a grinding sound followed by the operator timing out and reporting a fault.
- Gate stops halfway and reverses. The controller thinks it hit an obstruction. The cause is often a current-sensing threshold set too tight, but if it happens on every cycle regardless of load, the motor windings are drawing high current and the motor is on its way out.
- Operator beeps and refuses to start. On Ghost Controls this is frequently the battery or the solar charge circuit, not the motor. We test both before recommending a motor, so you don’t pay for a motor you didn’t need.
- Manual release won’t disengage the arm. The release mechanism seizes from dust and heat, and a seized release often means the arm internals are worn past the point of a rebuild. Common on Summerlin gates that get full afternoon sun.
- Gate moves slowly or sounds labored. The motor is drawing more current than it should, usually because of worn brushes, a failing capacitor, or a gearbox that’s out of grease. Left alone, this burns out the controller.
See the difference
Before
After
Before
After
Before
After
Before
AfterReplacement Cost & What’s Included
For a Summerlin install of a Ghost Controls-compatible motor, plan on $680 to $1,250 installed. The low end covers a standard single-arm swing operator with a reusable bracket and control box. The high end covers a heavy-duty arm, a new controller, a new battery harness, and re-bracketing when the original mount has shifted. Dual-gate setups run higher. Parts and labor are broken out separately on the written quote, and we don’t add trip fees or “diagnostic” charges on top of the number we hand you.
What’s included: the motor, the mounting hardware if needed, the wiring check, controller programming, a full cycle test with the gate in both directions, limit switch and obstruction-sensing verification, and a photo record of the install left with you. The work is covered by the 365-Day Done Right Promise – if the motor or our install isn’t right within a year, we make it right at no charge. Under the Haven Standard, every visit includes documented evidence, so the next technician who ever touches this gate knows what was set and why.
DIY or Call Us?

Safe to check yourself: the model plate, the battery voltage at the controller terminals, whether the manual release disengages cleanly, and whether the gate itself swings freely with the arm disconnected. If the gate binds when pushed by hand, the problem isn’t the motor, and no replacement motor will fix it. Stop there and call.
Where DIY goes wrong on this specific part: a swing-gate arm carries significant spring load and the bracket is under tension when you try to swap it. The wiring is low-voltage but the controller is not forgiving – a mis-wired motor or reversed limit wires can fry a new board on first power-up, and the gate can run the wrong direction into a fence or a car. We’ve seen this in Summerlin more than once. A Ghost Controls motor replacement takes one of our technicians 2 to 3 hours including the cycle test and documentation. Call (844) 797-2809 for a written price before any work starts.
FAQs
How long does a Ghost Controls gate motor last in Summerlin? Expect 7 to 10 years in normal use, less if the gate is in full afternoon sun or if the arm has been running against a binding gate for years. Summerlin’s summer heat degrades the grease in the gearbox faster than cooler climates, and we typically see motor failures here several years earlier than in similar installs at higher elevation.
Can my Ghost Controls motor be repaired instead of replaced? Sometimes, yes. Brushes, capacitors, control boards, battery harnesses, and limit switches are all replaceable and we do those repairs. If the gearbox is stripped or the windings are shorted, replacement is the honest answer. We tell you which one you’re facing, in writing, before you commit to either.
How long does the swap take? Two to three hours for a standard single-arm replacement including the panel programming, the limit set, the obstruction test, and the photo record. If the original bracket has moved or the wiring needs to be re-run, add an hour. We schedule it as one visit.
How do you source the part? We order the Ghost Controls part by model number and manufacturing date, not by “looks close enough.” OEM unless an aftermarket equivalent is the better call for your series, in which case the exact part number is on your written quote. We don’t carry motors in a truck – the part is ordered and scheduled, and you know the price before we order.
When your gate won’t open and you need it back online, call (844) 797-2809. We’ll give you a written price, tell you whether it’s a repair or a replacement, and put the evidence on paper when we’re done. Vance Gate Repair Summerlin is an independent service provider working with Ghost Controls equipment – we’re not affiliated with Ghost Controls – and we service LiftMaster, Mighty Mule, DoorKing, and other major brands too.
Written by the team at Vance Gate Repair Summerlin, serving Summerlin and nearby areas.