Wrought iron
Wood & steel frame
Farm & ranch
Sliding driveway gates
LiftMaster operatorsFree on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Get your free estimateGhost Controls Gate Parts & Welding in Summerlin: What to Know First
We provide independent Ghost Controls gate parts and welding in Summerlin, and most swing-gate repairs here are finished in a single visit once the right part is on hand. Simple fixes like hinge replacement, latch adjustment, or a bent rail run $185 to $420; custom welding and post replacement run higher because the gate has to come down, get set, and be tested against the operator. The honest part: we quote in writing before anyone picks up a tool, and if the part you need has to be ordered, we tell you that up front rather than after.
This page is for the homeowner with a Ghost Controls operator already mounted on a wood or steel driveway gate who has a sagging hinge, a dragging gate, a post that’s pulled loose, or a weld that let go. If that’s you, call (844) 797-2809 and a live person answers, day or night.
How Ghost Controls Products Fail – and How We Fix Them
Ghost Controls builds a solid DIY-oriented operator, and it’s popular in Summerlin for exactly that reason: the automatic gate opener kits are sold direct and installed by handy homeowners. The failures we see are rarely the control board. They’re the gate structure around it and a handful of parts the operator stresses hardest.
- The gate sags and the operator takes the blame. On Ghost Controls automatic gate opener kits mounted to wood gates, the most common call we get is “the opener quit.” Almost always the post has shifted or a hinge has worn, and the arm is now fighting a gate that’s dropped a half inch. We measure the gate’s swing, check the post for movement, and fix the structure before touching the operator. Replacing a control board on a sagging gate just burns a board.
- Hinge and post failure on heavier gates. Ghost Controls single and dual swing kits are frequently paired with gates heavier than the light-duty hinges were meant to carry. The hinge pin wears oval, the gate drops, and the arm bracket takes the load. We replace the hinge with a heavier-rated set and re-hang the gate to the operator’s specified geometry.
- Rail and weld fatigue. Steel tube gates in Summerlin take a real beating from the summer heat cycle, expanding by day and contracting overnight. Welds at the rail-to-stile joint crack first. We cut out the failed weld, re-weld with proper penetration, and dress it so the gate reads clean.
- Latch and lock misalignment. When a gate drops even slightly, the latch stops catching. Homeowners often bend the latch to compensate, which makes it worse. We realign the gate and reset the latch and lock to the correct gap.
- Rollers and guides binding. Sliding setups and gate rollers on Ghost Controls-equipped gates seize from grit and heat. We replace the roller set and check that the gate tracks true.
One detail you won’t find on Ghost Controls’ own site: a surprising number of “operator failure” calls on their swing kits trace back to the arm bracket bolts loosening after a single season, not to the motor or board at all. We torque and document those bolts on every visit so the next technician isn’t chasing a ghost.
Styles & brands we work with
- Wrought iron
- Wood & steel frame
- Farm & ranch
- Sliding driveway gates
- LiftMaster operators
Our Ghost Controls Gate Parts & Welding Process

- 1
Phone diagnosis. A live person takes the call at any hour and asks the model, the gate material, and what the gate is doing. We tell you the likely cause and a rough range before we roll.
- 2
On-site inspection. We test the gate’s swing by hand with the operator disengaged, check post plumb, hinge wear, and weld condition, and photograph everything we find.
- 3
Parts decision. For Ghost Controls parts we weigh OEM against quality aftermarket and tell you the trade-off in plain terms, including what it means for your warranty. You get the written price before any work starts.
- 4
The repair. Hinge replacement, post reset, rail repair, custom welding, roller or latch work, done to spec and re-checked against the operator’s travel limits.
- 5
The test. We cycle the gate through full open and close, confirm the safety reverse works, and adjust the arm bracket geometry so the operator isn’t fighting the gate.
- 6
The record. Before we leave, you get a photo log of every adjustment, the part numbers installed, and the written scope. That record is covered by our 365-Day Done Right Promise.
See the difference
Before
After
Before
After
Before
After
Before
AfterWhat Ghost Controls Gate Parts & Welding Costs in Summerlin
These are the ranges Summerlin homeowners actually see. Your written quote locks the number before work begins.
| Job | Typical Range |
|---|---|
| Hinge replacement (per hinge, heavier-rated set) | $185 – $320 |
| Latch and lock realignment | $145 – $260 |
| Gate roller replacement (set) | $160 – $290 |
| Rail repair / re-weld | $220 – $480 |
| Custom welding (cracked frame, bracket repair) | $275 – $650 |
| Post replacement / reset | $450 – $1,100 |
What moves the price: gate material (wood vs steel), whether the post has to be dug out and reset in concrete, and whether the part is on hand or ordered. We’re independent, so we’re not steering you toward a replacement operator when a hinge and a weld will do. Estimates are free. Call (844) 797-2809.
Why Summerlin Homeowners Call Vance Gate Repair Summerlin for Ghost Controls Work

We service nine major automation brands, so we work on whatever operator is already on your property rather than pushing a swap. Our technicians have up to 12 years of experience, and they know Ghost Controls swing kits well enough to tell the operator problem from the gate problem on the first visit. Every job comes with a written price before work starts, a photo record when we leave, and the 365-Day Done Right Promise: if the repair isn’t right, we make it right at no additional charge. As an independent Ghost Controls service provider, we’re not affiliated with or authorized by Ghost Controls, so we give you a straight parts recommendation instead of a manufacturer party line. We also handle LiftMaster, Mighty Mule, and DoorKing when a property has a mix. Bring us a written estimate from another company and we’ll review it free.
FAQs
We use genuine Ghost Controls parts where the warranty or a specific fit demands it, and quality aftermarket where it’s equal or better for less. We explain the trade-off in writing so you decide, and we never install a part that would quietly void your operator warranty without telling you first.
Most common parts (hinges, rollers, latches, brackets) we carry or source fast, often same day. Less common parts may need to be ordered, and we’ll tell you that up front with a written price so there’s no surprise. Call (844) 797-2809 for a straight answer on availability.
More often than not it’s the gate, not the operator. A sagging hinge, shifted post, or cracked weld makes the arm fight the gate, and the operator trips out. We diagnose the structure first, fix it, and only then decide if any Ghost Controls part needs replacing.
Repair is almost always the right call when the frame and post are sound. A hinge, weld, or latch repair keeps a working operator working. We only raise replacement when the frame is structurally gone, and we’ll show you the photos that make that case.
We answer the phone 24/7 and can often reach most Summerlin repairs the same day or next, depending on part availability. You’ll get a written price before any work starts, so you know the cost before we arrive. Call (844) 797-2809.
If your Ghost Controls gate is sagging, dragging, or won’t latch, call (844) 797-2809 for a free estimate. A live person answers day or night, we quote in writing before work begins, and every visit leaves you a documented record of what we found and what we fixed.
Written by the team at Vance Gate Repair Summerlin, serving Summerlin and nearby areas.