Wrought iron
Wood & steel frame
Farm & ranch
Sliding driveway gates
LiftMaster operatorsFree on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Get your free estimateGhost Controls Gate Access Control in Summerlin: What to Know First
Vance Gate Repair Summerlin provides independent service for Ghost Controls gate operators and their access-control add-ons – keypads, remotes, phone-entry modules, card readers, intercoms, and smart-access bridges – and most Summerlin jobs are diagnosed and quoted within a single visit. We’re an independent Ghost Controls service provider, not an authorized dealer, which means we fix the operator you already own instead of steering you into a new one. The price is written and handed to you before any work starts, so there’s no invoice surprise when we leave. Call (844) 797-2809 and a live person answers, day or night.
This page is for the Summerlin homeowner who already owns a Ghost Controls system, has probably read the manual twice, and wants to know what’s actually wrong before someone starts charging for it.
How Ghost Controls Products Fail – and How We Fix Them
Ghost Controls builds a solid DIY-friendly operator, and that’s exactly where the service pattern shows up. These are the failures we see most often on Summerlin gates, and what each one really means.
- Keypad codes that stop working after a firmware-era board swap. On Automatic Gate Opener series units paired with the Ghost Controls wireless keypad, a replaced control board often ships with a different access-code structure than the original, and previously saved codes silently drop out. We reprogram the keypad against the new board’s actual code slots and photograph the code sheet before we leave.
- Remotes that work close but fail from the driveway. Ghost Controls remotes run on a fixed-frequency receiver, and a weak or aging receiver antenna lead is the usual culprit – not the remote. We test signal strength at the receiver, not just at the gate, and confirm whether a replacement remote or a receiver-side fix is the honest answer.
- Phone-entry and smart-access modules that drop offline. The Wi-Fi and app-control add-ons depend on a stable power lead and a clean ground; a corroded connection at the operator’s control box will knock the module offline while the gate itself still opens by remote. We trace the power and ground first, because a module swap won’t fix a bad ground.
- Safety photo-eye (the infrared beam that reverses the gate if something crosses the path) misalignment. Summerlin’s sun angles and the way desert dust settles on the lens push these out of line more than most owners expect. A beam off by two inches reads as an intermittent stall. We realign, clean, and record the new position with a photo.
- Limit switches drifting past travel. Ghost Controls arms set slightly beyond the gate’s physical travel will stall, reverse, or trip the board’s fault light. We reset the limits to actual travel, mark the setting, and note the reading on your paperwork so the next technician isn’t guessing.
Styles & brands we work with
- Wrought iron
- Wood & steel frame
- Farm & ranch
- Sliding driveway gates
- LiftMaster operators
Our Ghost Controls Gate Access Control Process

- 1
Phone intake. We note the Ghost Controls model, which access devices are on the gate, and the symptom. A live person takes this, not a form.
- 2
On-site diagnosis. We read the control board, test the receiver and keypad, check power and ground at the access module, and inspect the photo-eyes and limits. You see what we find.
- 3
Written price before work. We hand over the flat price for the diagnosed repair, along with the OEM-versus-aftermarket parts decision. If an aftermarket part is the right call, we say so and say why. You approve before a tool comes out.
- 4
The repair. Wiring, code reprogramming, module replacement, beam alignment – whatever the diagnosis called for, done to the written scope.
- 5
The test. Every access device is cycled: keypad, remotes, phone entry, and the safety reversal. We don’t leave until each one behaves.
- 6
The record. You get a photo log of what was found, what was adjusted, and what was installed, plus part numbers. The 365-Day Done Right Promise covers the work.
Before
AfterWhat Ghost Controls Gate Access Control Costs in Summerlin
These are real ranges for the work, not teaser numbers. Every figure is confirmed in writing before we start.
| Job | Typical Range |
|---|---|
| Keypad reprogramming / code reset | $95 – $165 |
| Remote or receiver diagnosis and fix | $120 – $240 |
| Phone-entry / smart-access module repair | $150 – $320 |
| Photo-eye realignment and safety test | $110 – $210 |
| Control board replacement (access-related) | $280 – $520 |
What moves the price: whether the board needs replacing, whether an access module is under separate warranty, and how accessible the control box is. Call (844) 797-2809 for a free written estimate.
See the difference
Before
After
Before
After
Before
AfterWhy Summerlin Homeowners Call Vance Gate Repair Summerlin for Ghost Controls Work

We’re not the only company in Summerlin that will touch a Ghost Controls operator, but we’re the one that leaves you a written price before work starts and a photo record after. The 365-Day Done Right Promise covers every repair for a full year – if it’s not right, we make it right at no charge, no argument. Our technicians bring up to 12 years of experience and work on nine automation brands, so if your gate carries a LiftMaster, Mighty Mule, or DoorKing instead, we’re still the right call. Background-checked, uniformed technicians, name and photo before arrival. A live person answers at any hour.
FAQs
Our labor on the repair is covered by the 365-Day Done Right Promise for a full year. Ghost Controls’s own manufacturer warranty on parts is separate, and we’ll tell you plainly whether a part is still under it before recommending a replacement.
Yes. We source OEM Ghost Controls parts where they’re the right fit and quality aftermarket equivalents where they’re not, and we explain which is which. The part number goes on your written record either way.
Repair is usually the right call on a Ghost Controls unit with a working motor and a failing access component – keypad, receiver, module, or beam. We’ll say so directly if a replacement makes more sense, but we don’t start there.
Most access-control diagnostics are scheduled quickly, and a live person takes your call 24/7. We give you an honest window on the phone, not a range that moves.
Yes – we service nine automation brands including LiftMaster, Mighty Mule, and DoorKing. One company can handle whatever motor is already on the property.
Get Your Ghost Controls Gate Access Control Fixed

Call (844) 797-2809 for a free estimate on your Ghost Controls access-control repair in Summerlin. A live person answers around the clock, the price is in writing before we start, and you get the photo record when we’re done.
Written by the team at Vance Gate Repair Summerlin, serving Summerlin and nearby areas.