Wrought iron
Wood & steel frame
Farm & ranch
Sliding driveway gates
LiftMaster operatorsFree on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Get your free estimateMighty Mule Welding & Fabrication: The Summerlin Owner’s Guide
Welding and fabrication repair for a Mighty Mule gate in Summerlin typically runs $250 to $650 for the bracket, hinge, post, and frame work itself, plus $95 to $180 for the on-site labor to fit and align it. We weld on site and in our fabrication shop, and most Summerlin calls are scheduled within one to three business days. Under the Haven Standard, you get the written price before the torch is lit.
Owners usually find this problem in stages. First there’s a gate that drags at the bottom of its arc. Then a hinge that looks bent, or a bracket mount that has cracked along the weld. Then, on a windy afternoon in Summerlin, the whole thing shifts a quarter inch and the opener starts throwing its limit switch. The motor isn’t the problem. The frame has lost its shape.
Which Mighty Mule Models This Applies To
Mighty Mule is a common sight on Summerlin driveways, especially the MM series (MM360, MM560, MM660) and the E-Z Gate line, plus the heavier GM and FM series on wider ranch-style gates. The welding and fabrication work doesn’t depend on the model number, but it does depend on the gate itself. Here’s the thing to check: the gate’s leaf weight and its material. A hollow aluminum gate welds differently from a steel tube one, and a wood gate needs a different mounting approach entirely. Most of the parts we fabricate are steel hinges, gate brackets, ground stops, and post caps, and each one is measured on site before we cut.
Before we quote anything, we look at the label plate on the gate frame or on the opener housing, and we measure the leaf width and thickness. That plate number tells us the gate’s rated duty and its intended weight. Getting that wrong is one of the most common ways a Summerlin owner pays twice.
We are an independent service provider, not affiliated with Mighty Mule, and we don’t carry a parts inventory on a truck. That’s a deliberate choice. Every bracket we install is measured, cut, and welded to your gate, not pulled from a shelf and fitted with a hammer.
Styles & brands we work with
- Wrought iron
- Wood & steel frame
- Farm & ranch
- Sliding driveway gates
- LiftMaster operators
Signs Your Mighty Mule Welding & Fabrication Is Failing

The failure usually announces itself through the gate’s behavior before you see a crack. These five symptoms are the ones we see most often in Summerlin:
- The gate drags at the bottom of its swing. That’s a hinge that has bent beyond its design pitch or a bracket mount that has pulled slightly out of square. You’ll feel it as a hesitation at the start of the arc.
- A visible crack in the bracket, hinge plate, or frame weld. A fatigue crack at a weld toe is a sign the original weld bead didn’t have enough penetration for the gate’s weight. Left alone, it grows.
- The opener strains or the arm binds mid-travel. If the gate is no longer square to the post, the swing arm has to fight the geometry. The opener often gets blamed for a frame problem.
- The gate sticks in cold weather and frees up as it warms. Here that’s usually the opposite of snow country: in Summerlin’s dry heat, a shrinking weld can open a hairline crack that closes again at night. It’s the seasonal swing that gives it away.
- Wobble at the post cap or the ground stop has shifted. The base plate or post cap anchor has loosened, or the concrete beneath the post has cracked. Either way, the gate loses its reference point and the opener can’t hold a consistent limit.
See the difference
Before
After
Before
After
Before
After
Before
AfterReplacement Cost & What’s Included
Here’s the honest installed range for Summerlin, based on what we actually weld and fit. These aren’t estimates pulled from a national average; they’re what our written quotes come out at on a Summerlin driveway.
| Work | Typical installed cost |
|---|---|
| Hinge replacement or re-weld, per hinge | $150 – $280 |
| Gate bracket fabrication and fit | $220 – $420 |
| Post cap or ground stop replacement | $180 – $350 |
| Frame straightening and re-square | $300 – $650 |
| Full frame weld-out and alignment | $500 – $1,100 |
| On-site labor (fit, measure, align) | $95 – $180 |
| Shop fabrication of a custom bracket | $120 – $300 |
The range depends on the gate’s weight, whether the post is sound, and whether we fabricate a custom piece or fit a standard one. You get a written price before any work starts, with the part number and the weld spec on the page. Under Clause 4 (Evidence on every job), we photograph every weld, bracket, and adjustment, so you have a record of what was changed. And the 365-Day Done Right Promise covers the work for a full year.
DIY or Call Us?

Welding a gate bracket is hot, high-current work done near your opener, your wiring, and your gate’s spring, and I’ll be plain with you: this isn’t a job for a homeowner with a shop welder and a free afternoon. There’s a real chance of a warped frame, a fire in the wiring run, or a gate that swings off its arc and puts load on the opener motor. A licensed technician should do the weld. What you can safely do yourself is look: measure the gap between the gate leaf and the post, photograph any crack, note where the hinge is worn, and check that the gate still latches by hand. That’s the paperwork we want to see.
For the rest, call (844) 797-2809. We’ll pick up, and we’ll bring the written price.
FAQs
Most fabricated steel brackets and hinges hold up 8 to 15 years in Summerlin’s climate, depending on whether the original was galvanized or painted. The dry desert air is kind to steel; the UV and the heat cycles are what wear the coating first, so touch-up paint every few years buys years of life. Call (844) 797-2809 for a quote on your gate.
Often, yes. A hairline weld crack, a bent hinge plate, or a loosened bracket can be re-welded, re-squared, or re-secured instead of cut out. If the frame itself is distorted beyond its design, replacement is the right call, and we’ll tell you that honestly. Call (844) 797-2809 to see which side of that line your gate is on.
Most single-part replacement jobs run about 1 to 3 hours on site, and a full frame re-weld or re-square takes longer, more like 4 to 6 hours. We give you the schedule when we quote. Call (844) 797-2809 for a free estimate.
Every bracket and hinge is fabricated to your gate’s measurements, so the price reflects your actual gate rather than a stocking fee. You get the written price before work starts, and the part number goes into the photo record we leave with you. Call (844) 797-2809 for a free estimate.
Written by the team at Vance Gate Repair Summerlin, serving Summerlin and nearby areas.