Wrought iron
Wood & steel frame
Farm & ranch
Sliding driveway gates
LiftMaster operatorsFree on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Get your free estimateMighty Mule Access Control Installation: The Summerlin Owner’s Guide
We install Mighty Mule-compatible access control in Summerlin, and most residential jobs land between $650 and $1,450 installed, depending on whether we’re fitting a keypad and exit device to an existing Mighty Mule operator or replacing failed entry hardware. Repair and replacement calls are usually handled same day; new access-control installations are measured, ordered and scheduled. Summerlin owners typically discover the problem the same way: the keypad stops taking the code they’ve used for years, or the gate stops responding to the clicker, and it turns out the receiver or control board has been drifting for months.
Vance Gate Repair Summerlin is an independent service provider. We’re not affiliated with Mighty Mule, and we don’t steer you toward a new unit when the access hardware is what failed.
Key Takeaways
- Most Mighty Mule access-control installs in Summerlin run $650-$1,450 installed.
- Your written price arrives before any tool comes out, every time.
- We service nine automation brands, so whatever motor is on the property is the motor we work on.
- Every visit leaves a photo log of what was found, set and installed.
Which Mighty Mule Models This Applies To
Mighty Mule’s residential line splits into two families that matter here. The M-series (MM260, MM360, MM560 and the MM571-style single-arm swing operators) uses control boards with an on-board receiver, so an access-control add-on has to be compatible with the board generation in the housing, not just the model name. The older 350/500 series units use a different board layout and a different terminal strip. Same brand, different wiring. This is where most DIY keypad installs go wrong.
Identify your unit from the label inside the control box cover, not from memory. The label carries the model and the board revision, and the revision is the number that decides which receiver and keypad harness will actually talk to the operator. If the label is sun-faded (common in Summerlin after a few summers), photograph the board itself; the terminal layout is often enough for us to identify the generation.
On the OEM-versus-aftermarket question, Mighty Mule is honest about this: genuine boards and receivers cost more but drop in without adapter work, while quality aftermarket equivalents are cheaper and sometimes better built for heat. We’ll quote both in writing and tell you which one we’d put on our own gate.
Styles & brands we work with
- Wrought iron
- Wood & steel frame
- Farm & ranch
- Sliding driveway gates
- LiftMaster operators
Signs Your Mighty Mule Access Control Installation Is Failing

- The keypad accepts the code but the gate doesn’t move. Usually a failed relay on the control board or a corroded terminal at the keypad harness. The code is fine; the signal isn’t reaching the operator.
- The gate opens on its own at odd hours. Almost always a mis-set receiver picking up a neighbor’s remote or a failing board with a stuck input. In Summerlin’s dense walled communities, shared frequencies make this more common than you’d expect.
- The clicker only works from a few feet away. A dying receiver or an antenna that’s been pinched against the housing during a prior install. Range drops before it dies completely.
- The exit wand or loop stops triggering. Failed loop detector, damaged saw-cut in the driveway, or a wand that’s taken on water. Common after monsoon season.
- The board has visible heat discoloration. Desert heat ages control boards faster than the manufacturer’s spec sheet suggests. Brown marks near the relay are the tell.
See the difference
Before
After
Before
After
Before
After
Before
AfterReplacement Cost & What’s Included
Installed pricing for Summerlin, quoted in writing before work starts:
| Scope | Installed Range |
|---|---|
| Wireless keypad + receiver retrofit | $650 – $850 |
| Wired keypad + control board replacement | $850 – $1,150 |
| Full access-control package (keypad, exit device, receiver) | $1,150 – $1,450 |
| Board-only repair, existing hardware | $280 – $450 |
The range is driven by board generation, whether a power run to the keypad exists, and gate travel. Under the Haven Standard, that flat price is written and handed over before any work starts – no surprise invoice at the end. Completed work carries our 365-Day Done Right Promise: if the repair isn’t right, we make it right at no additional charge within that year.
DIY or Call Us?

You can safely check three things yourself: whether the keypad has power (most have a small LED), whether the gate opens from the wall-mounted push button instead of the keypad, and whether any terminals in the control box look loose or corroded with the power off. That’s the safe list.
Where DIY goes wrong: the control box carries line voltage, and the operator’s arm is under spring tension. A board swap done with the power on, or a receiver wired to the wrong terminal, can fry the operator or hurt you. For anything past the visual check, call us at (844) 797-2809 and we’ll give you a written price before we touch it.
FAQs
How long does a Mighty Mule access-control setup last in Summerlin? Expect seven to ten years on the board and keypad in our climate, sometimes less if the housing sits in full afternoon sun. Desert heat is the main killer; UV-degraded keypad membranes and heat-aged relay contacts fail first.
Can it be repaired instead of replaced? Often, yes. A failed relay or a corroded harness can be repaired at a fraction of replacement cost, and we’ll tell you honestly which is worth doing. We quote both.
How long does the swap take? A keypad-and-receiver retrofit is a half-day job. A full package with board replacement and exit device runs a full day. We confirm the window when we schedule.
How do you source the part? We match the part to your board revision from the label and terminal layout, quote OEM and quality aftermarket options in writing, and order the one you approve. We also service LiftMaster, Ghost Controls, DoorKing and six other brands, so if the operator itself needs attention while we’re there, we handle it in the same visit.
Call (844) 797-2809 for a free estimate. Written price before work starts, a documented photo record when we leave, and a live person answering at any hour. If you have a written estimate from another company, bring it and we’ll review it at no cost.
Written by the team at Vance Gate Repair Summerlin, serving Summerlin and nearby areas.