Wrought iron
Wood & steel frame
Farm & ranch
Sliding driveway gates
LiftMaster operatorsFree on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Get your free estimateMighty Mule Gate Motor Replacement: The Summerlin Owner’s Guide
We replace failed and failing Mighty Mule gate motors in Summerlin, and most residential swing-gate motor replacements run between $650 and $1,450 installed, depending on the model, arm condition, and whether the control board or battery is also being replaced. Mighty Mule failures are usually diagnosed the same day you call, and a live person answers around the clock. Most Summerlin owners discover the problem the same way: the gate stops midway, reverses for no reason, or the arm runs but the gate doesn’t move. The motor housing fills with rainwater, a limit switch drifts, or the battery in a solar unit quietly gives out after a few summers of desert heat. You press the remote, nothing happens, and the gate sits open toward the street.
Which Mighty Mule Models This Applies To
Mighty Mule sells single and dual swing-gate operators across several series, and the motor assembly, control board, and arm hardware are not interchangeable between them. The single-arm units (the MM260, MM360, and similar single operators) use a different arm length and control board than the dual-gate MM560 and MM660 kits, where a second arm is slaved to the primary. Before we quote anything, we read the label inside the control box and measure the gate leaf, because the same model number can ship with different arm brackets depending on how the gate was hung.
On the OEM-versus-aftermarket question, Mighty Mule parts are widely available, and a quality aftermarket arm or board is a reasonable choice for an older operator that’s otherwise sound. What matters more than the badge on the box is matching the connector and the control board revision, since Mighty Mule changed board layouts between production runs and a board that fits one year of a model won’t plug into another. We’re an independent service provider, not affiliated with Mighty Mule, so we quote the part that fits your gate rather than steering you toward a full replacement when the arm and board are still good. We also service LiftMaster, Ghost Controls, DoorKing, and other brands on the same driveway.
Styles & brands we work with
- Wrought iron
- Wood & steel frame
- Farm & ranch
- Sliding driveway gates
- LiftMaster operators
Signs Your Mighty Mule Gate Motor Replacement Is Failing

- The gate opens a few feet and reverses. A misaligned limit switch or a failing control board is telling the operator the gate hit an obstruction. We read the limit position and photograph it before any reset.
- The arm runs but the gate barely moves. Usually a stripped gear inside the actuator or a worn arm bracket, not a power problem. The motor is turning; the linkage has let go.
- The gate won’t hold its position when pushed by hand. The actuator has lost its mechanical resistance, and the operator is running on borrowed time.
- A solar unit that stalls after two or three summers. Summerlin’s heat shortens battery life, and a battery that no longer holds a charge mimics a dead motor. We test the battery before quoting a motor.
- Dead on the remote, but the manual release still works. A control board or receiver fault. The gate opens by hand because the mechanics are fine; the electronics are not.
See the difference
Before
After
Before
After
Before
After
Before
AfterReplacement Cost & What’s Included
In Summerlin, most Mighty Mule motor replacements land between $650 and $1,450 installed, including the part and labor. A straight single-arm swap with an intact bracket sits near the low end. A dual-gate operator, a rusted or bent arm bracket that has to be cut and re-welded, or a control board that needs replacing alongside the motor pushes toward the top. We write the flat price and hand it to you before any work starts, so there’s no invoice surprise at the end.
Under the Haven Standard, every visit includes a photo record of what we found and what we installed, and the 365-Day Done Right Promise covers the work for a full year. If the replacement isn’t right, we make it right at no additional charge.
Standard residential Mighty Mule replacement, Summerlin: $650 to $1,450 installed, depending on model and hardware. Ask for the written estimate before work begins.
DIY or Call Us?

You can safely do a few things yourself: check the breaker or solar fuse, test the remote battery, and confirm the manual release still engages. Gate motor replacement is a different matter. A Mighty Mule operator mounts to a charged circuit with a low-voltage transformer, and a dual-gate system has a second arm synchronized to the primary. A limit switch set wrong, or a board wired with the wrong polarity, can run the gate into a stop and damage the mechanism, or leave a live circuit in a junction box you can’t see. This is work for a trained technician, not a weekend project. When you’re ready, call (844) 797-2809 for a free estimate and we’ll tell you exactly what’s failing before anyone touches a tool.
FAQs
Most Mighty Mule operators in Summerlin last 8 to 12 years, and desert heat shortens that on solar units where the battery is the first thing to go. The first replacement usually comes around year 8, and if you’re already past 10, the motor is living on borrowed time. Call (844) 797-2809 and we’ll test it before you spend on a part.
Often, yes. A failed limit switch, control board, or battery is a repair, not a replacement, and we check those first. We only quote a full motor replacement when the actuator itself has lost its gear or resistance. Call (844) 797-2809 for a free second opinion, and bring any written estimate from another company; we’ll review it at no cost.
A single-arm swap in Summerlin usually runs two to three hours; a dual-gate operator with a second arm takes most of a morning. We don’t leave until the limits are set, the remote is paired, and you’ve seen the photo record of what changed.
We match the part to the label inside your control box and order the board revision and arm bracket that fit your operator, then install it. We don’t carry stock on a truck, so we confirm the part number before scheduling. Call (844) 797-2809, and we’ll write the price and hand it over before any work starts.
Call (844) 797-2809 for a free estimate. A live person answers 24 hours a day, and we’ll tell you what’s failing, quote the part and labor in writing, and get your gate working again.
Written by the team at Vance Gate Repair Summerlin, serving Summerlin and nearby areas.