Wrought iron
Wood & steel frame
Farm & ranch
Sliding driveway gates
LiftMaster operatorsFree on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Get your free estimateWhy Summerlin Homeowners Choose Ghost Controls Gate Repair
We provide independent Ghost Controls gate repair service in Summerlin, NV, for owners of the DIY, Viking, and Titan lines. What separates our Ghost Controls work is model-level familiarity: we know how these boards, battery packs, and tube-gate arms actually fail in desert heat, and we price the repair in writing before a tool comes out. We are an independent service provider, not affiliated with or authorized by Ghost Controls, and we answer the phone 24/7 at (844) 797-2809.
Ghost Controls operators are common on Summerlin driveway gates because they’re sold as homeowner-installable systems, and a lot of them were installed by the homeowner or a handyman rather than a gate technician. That history matters when something goes wrong. An operator that was mounted two degrees out of plumb, or wired to a photocell (the infrared beam that stops the gate if something crosses its path) that was never aligned, will develop problems that look like a board failure but aren’t. We sort that out before recommending parts.
Why Trust Vance Gate Repair Summerlin for Your Ghost Controls Gate Repair?
Our technicians have up to 12 years of experience, and Ghost Controls units come through our Summerlin work every week. That means we’ve seen the same failures repeat: swollen battery packs, boards with heat stress around the solder joints, limit switches that drifted a few degrees after a temperature swing. Knowing the pattern shortens diagnosis. We’re not guessing at your gate.
Parts matter on this brand. Ghost Controls uses proprietary control boards and arm geometries, and an aftermarket board that “fits” a DIY-3132 isn’t the same board. We source genuine Ghost Controls control boards, arms, and battery packs when the OEM part is the reliable fix, and we use quality aftermarket equivalents only for wear items like hinges, photosensors, and remotes where they meet or exceed the original spec. That approach keeps your operator warranty intact where it can be kept, and we’ll tell you plainly when a part choice would jeopardize it.
Every job runs under The Haven Standard. You get a written price before any work starts, a photo record of what we found and what we set, and the 365-Day Done Right Promise covering the completed repair. Before a technician arrives you get their name and photo. Under Clause 4 (Evidence on every job), the photo log is included on every visit at no additional charge.
Styles & brands we work with
- Wrought iron
- Wood & steel frame
- Farm & ranch
- Sliding driveway gates
- LiftMaster operators
Common Ghost Controls Gate Repair Problems We Fix in Summerlin

These are the failures we actually see on Ghost Controls operators in Summerlin, named by the model family they tend to hit.
- Control board water intrusion and heat fatigue on DIY-series boards (DIY-3132, DIY-3722). These boards are often mounted in enclosures that get direct afternoon sun, and Summerlin’s 100°F-plus summers cook the solder joints over a few seasons. Symptoms show up as erratic behavior: the gate runs fine in the morning and misbehaves once the enclosure heats up. Resealing the enclosure without addressing the board just delays the failure.
- Battery backup packs failing early. A Ghost Controls backup pack in a Summerlin enclosure lives a harder life than the spec sheet assumes. High ambient temperature plus daily recharge cycling ages the pack fast, and a weak pack causes intermittent open/close faults that look like a logic problem. We test voltage under load, not just at rest, because a rested pack can read fine and still collapse under the arm’s draw.
- Limit-switch drift and arm binding on the Viking (VK-3722) and Titan (TDS-3722) swing arms. Seasonal temperature swings move the arm geometry enough that the limit switch lands a few degrees past travel. The gate stops short or reverses mid-travel. It’s a reset and re-teach job most of the time, not a board replacement, and it’s worth confirming the arm isn’t binding at the same time.
- Remote and keypad pairing dropouts. These usually trace to antenna placement inside a metal enclosure, low battery voltage in the remote itself, or a firmware reset after a power event. Re-pairing fixes the symptom; correcting the antenna routing fixes the cause.
- Post and footing settling behind “it just needs adjusting.” Summerlin lots sit on fill and caliche-laden soil, and expansive clay moves. A gate that’s out of plumb often has a heaving or settling post footing underneath, not a bad operator. Re-hanging the gate on a moving post is money spent twice.
Before
AfterGhost Controls Parts & Our Repair-vs-Replace Approach
We don’t keep Ghost Controls parts on hand locally. When a job needs a control board, arm, or battery pack, we identify the exact part number during diagnosis, put it in the written scope, and source it for the scheduled visit. That means you know what’s going in and what it costs before we start, and you’re not paying for a part pulled off a shelf on a guess.
The repair-versus-replace decision is where a lot of Ghost Controls owners get steered wrong. If a board or an arm has failed in isolation and the housing is sound, we repair it. If the housing, arm, and board are all degraded together, replacement is the smarter spend, and we’ll say so directly rather than quietly billing you toward a new operator. We service nine major gate-automation brands, so we have no reason to push a replacement you don’t need.
If you’ve had another company quote a Ghost Controls replacement, we’ll review their written estimate at no cost. Bring the paperwork and call (844) 797-2809.
Our Ghost Controls Service Process – Step by Step

- 1
Diagnosis. We test battery voltage under load, check limit-switch travel against the arm’s actual position, inspect the board and enclosure for heat stress and water intrusion, and verify the post and footing are sound. A Ghost Controls symptom that looks electrical is sometimes mechanical.
- 2
Written scope and price. You get the findings, the part numbers, and a flat price in writing before any work begins. Under Clause 1 (Have it in writing), that price doesn’t move after the job starts.
- 3
Repair or install. We replace the failed component with the OEM or spec-matched part named in the scope, re-teach the limits, and correct the underlying cause (enclosure shading, antenna routing, arm alignment) rather than only the symptom.
- 4
Test and document. We cycle the gate through full travel, test every safety edge and photo-eye, confirm remote and keypad pairing, and photograph the settings we left behind. You get that photo record before we leave.
- 5
Warranty. Completed work is covered by the 365-Day Done Right Promise. If the repair isn’t right within that window, we make it right at no additional charge.
A typical Ghost Controls swing-gate call starts with the gate reversing halfway or refusing to open in the afternoon heat; the owner often finds the battery-backup pack swollen or the control board showing heat stress. A qualified pro checks battery voltage under load, verifies limit-switch travel and arm alignment, and usually replaces the backup pack or board and re-teaches the limits rather than swapping the whole operator.
See the difference
Before
After
Before
After
Before
AfterGhost Controls Products We Service & Install in Summerlin
We service and install the Ghost Controls DIY Series (DIY-3132, DIY-3722), the Viking Series (VK-3722), the Titan Series (TDS-3722), and Ghost Controls solar-compatible DC swing operators with tube-gate arms. On the sub-service side, that covers battery backup replacement and testing, motor and arm repair, and smart access: phone entry, keypad, and remote pairing on existing operators.
Installation and new-operator work in Summerlin is measured and scheduled, not same-day. We’ll come out, measure the gate and the power situation, and give you a written price for the install. Repair calls are handled with more urgency, and the phone is answered by a live person at any hour.
We Also Service These Brands

Ghost Controls isn’t the only brand we work on, and we don’t steer anyone toward it. We service LiftMaster, Mighty Mule, DoorKing, and six other major gate-automation brands, so whichever operator is already on your property, we can diagnose it rather than pushing a replacement. If your gate has a Ghost Controls motor and a different brand’s keypad, that’s a normal day for us.
FAQs – Ghost Controls Gate Repair Service in Summerlin
No. We are an independent Ghost Controls service provider and are not affiliated with or authorized by Ghost Controls. We work on Ghost Controls operators because we know the product lines and their failure patterns, not because we carry manufacturer authorization. Call (844) 797-2809 with your model number and we’ll tell you what we can do.
Yes, for the parts where OEM is the reliable fix. Control boards, swing arms, and battery packs are sourced as genuine Ghost Controls parts matched to your model. For wear items like hinges, photosensors, and remotes, we use quality aftermarket equivalents where they meet or exceed OEM spec. The part number goes in the written scope before the job starts.
Most Ghost Controls repairs are a single visit, typically one to two hours on site once the correct part is in hand. Battery-pack and limit-switch work is often same-day. Board replacements depend on sourcing the exact model part, so those are usually scheduled. We confirm the timeline with the written price before we book.
We cover the DIY Series (DIY-3132, DIY-3722), Viking Series (VK-3722), Titan Series (TDS-3722), and Ghost Controls solar-compatible DC swing operators with tube-gate arms. If your model isn’t listed, call (844) 797-2809 with the number off the housing and we’ll confirm coverage.
Not when the work is done with the correct OEM part for the failed component, and we tell you upfront when a part choice could affect warranty coverage. We’re independent, so we can’t speak for Ghost Controls on a specific claim, but we document every part number and adjustment so you have what you’d need. Ask us before we start if warranty is a concern.
Most Ghost Controls repairs in Summerlin land in a written range based on the failed component: battery backup replacement generally runs in the low hundreds, limit-switch and arm re-teach work is typically at the lower end of the repair scale, and control board replacement sits higher depending on the model. The exact flat price is written and handed to you before any work starts, and it doesn’t change after. Call (844) 797-2809 for an exact quote. Estimates are free.
Book Your Ghost Controls Service in Summerlin, NV

Whether it’s a swollen backup pack, a Viking arm that binds in the heat, or a smart-access keypad that won’t pair, we’ll diagnose it, write the price, and document the fix. A live person answers the phone 24/7 at (844) 797-2809. Estimates are free, and we’ll review a written estimate from another company at no cost before you commit.
Written by the team at Vance Gate Repair Summerlin.