Wrought iron
Wood & steel frame
Farm & ranch
Sliding driveway gates
LiftMaster operatorsFree on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Get your free estimateFast, Reliable Gate Parts & Welding Across Whitney
If your gate is dragging, leaning, or seized after the last windstorm, we can help. Vance Gate Repair Summerlin handles hinge replacement, post replacement, rail repair, and custom welding for Whitney homeowners, and we work on the nine major automation brands already bolted to your property rather than pushing a new one. We know the 89122 ZIP well: the older tract streets tucked between Las Vegas and Henderson, where block walls and iron gates run right up to the flood-control wash. Most gate part jobs in Whitney are quoted in writing before anyone picks up a tool, with the price on paper in front of you. Call (844) 797-2809 and a live person answers, any hour.

Why Vance Gate Repair Summerlin Is Whitney’s Preferred Gate Parts & Welding Company
Whitney sits in unincorporated Clark County, so gate work here answers to county rules rather than City of Henderson or Las Vegas codes. We know the difference when we’re looking at a permit question on a post replacement. Our technicians have up to 12 years of experience, and they arrive with a written scope and a written price under The Haven Standard – Clause 1, have it in writing, holds on every visit to Whitney.
Every visit leaves a photo record: what we found, what we adjusted, what part went on. That matters in a neighborhood where gates are often original builder-grade hardware now 25 to 40 years old, and where the next technician shouldn’t have to rediscover a limit-switch setting or a hinge offset.
We cover Whitney’s 89122 without a callback queue. A background-checked, uniformed technician is dispatched, and you get their name and photo before arrival. See our full Gate Parts & Welding service for the wider picture.
Styles & brands we work with
- Wrought iron
- Wood & steel frame
- Farm & ranch
- Sliding driveway gates
- LiftMaster operators
Our Gate Parts & Welding Services in Whitney

If you’re comparing local gate specialists, we serve Whitney and the surrounding east valley for parts, welding, and getting a failing gate working again. Here’s what we handle most in these tract neighborhoods.
Post Replacement
Whitney’s shrink-swell soils loosen footings through the summer, and along the flood-control wash edge, flash-flood debris and blowing sand undermine the hinge post outright. When a post leans, no amount of hinge tightening fixes it. We dig out the old footing, re-set the post in concrete, and bring the gate back to true.

Hinge Replacement
Hinges seize from grit near the wash and rust from Mojave UV and low humidity. A worn hinge lets the gate sag and stresses the whole frame. We replace the hinge set and realign so the gate swings clean, with the new position photographed for the record.

Rail Repair
Monsoon winds knock solid infill gates out of alignment and bend rails, especially on the bigger panels older Whitney lots tend to have. We straighten or replace the rail and re-true the frame so the gate closes under its own weight without binding.

Custom Welding
Many Whitney gates are wrought iron or aluminum with block-and-iron perimeter styling from the 1970s through 1990s. When a bracket cracks or a stile separates, we weld it to match the original rather than swap the gate for something that doesn’t fit the wall.
Before
AfterTrusted Brands We Service in Whitney
We work on whatever motor is already on your property. Among the brands we service are Viking, Ghost Controls, DoorKing, and Elite, along with LiftMaster, FAAC, BFT, Linear, and Mighty Mule. We don’t claim to stock parts locally – what we do is identify the part, order or fabricate it, and schedule the return visit with a written price. That’s usually faster than waiting on a full replacement quote, and it keeps the operator you already own in service. Turnaround on common parts is typically quick once we’ve measured on site.
See the difference
Before
After
Before
After
Before
AfterCommon Gate Parts & Welding Problems We See in Whitney Homes

- Hinge posts undermined by sand and wash debris. Along the eastern edge toward the desert interface, grit loads up the hinge and the post footing loosens, so the gate sags and the hinges seize. This failure mode is rare in sheltered, newer Henderson subdivisions.
- Solid infill gates knocked out of alignment by monsoon wind. Big solid panels catch wind load, bending track and stressing the gate operator on slide gates. You hear the motor work harder than it should.
- Footings loosened by summer shrink-swell soils. The ground moves, the post leans, and the rack-and-pinion drifts out of mesh. The gate travels unevenly and jams at the ends.
- Rusted, worn builder-grade hardware. Whitney’s 1970s-90s tract homes often carry original gates with hardware that’s now decades old, and the hinge or latch simply gives out.
Pricing for Gate Parts & Welding in Whitney, NV
Here’s what gate parts and welding typically run in Whitney’s market:
| Job | Typical Whitney range |
|---|---|
| Hinge replacement (per hinge set) | $150 – $350 |
| Post replacement (dig, re-set, concrete) | $400 – $900 |
| Rail repair | $200 – $500 |
| Custom welding (bracket or stile) | $200 – $600 |
| Gate rollers or latch & lock | $120 – $350 |
Cost moves with post condition, soil, and whether the hardware matches the original. The flat price is written and handed to you before any work starts, so there’s no surprise at the end. Free estimate on every job.

We Also Serve Cities Near Whitney

We work across the east valley beyond Whitney too. If you’re in Sunrise Manor, Winchester, Paradise, or Las Vegas and your gate needs parts or welding, a written price and a photo record come standard. Call for a free estimate and we’ll confirm the scope before scheduling.
Serving Whitney, NV – Our Local Coverage Area
We serve Whitney and nearby communities. Use the map below to see the area we cover. If you’re nearby, we can almost certainly help.
FAQs – Gate Parts & Welding in Whitney

Use the manual release key or lever your operator manufacturer provides, turn off power at the breaker first, then disengage the motor per the owner’s manual before moving the gate by hand.
Never force a gate that won’t disengage – call us and we’ll walk you through the correct release for your brand (Viking, DoorKing, Elite, and others), by phone anytime.
Because the hinge post itself has usually shifted or been undermined, not the hinges. In Whitney, shrink-swell soil and wash grit loosen the footing, so tightening bolts only masks it briefly.
The fix is a post replacement: dig out the old footing, re-set in concrete, refresh the hinges, realign. Call (844) 797-2809 for a written price.
Clear the track and rollers of grit, and check whether the post has leaned enough to misalign the rack-and-pinion. If it’s still catching, a roller or track repair is usually the answer.
We can assess on site and quote it in writing before anything starts. Call for a free estimate.
Look for functioning photo-eyes (the infrared beam that stops the gate if something crosses the path) and, on some operators, safety edges. Test the beam by blocking it while the gate travels – it should reverse or stop.
If it doesn’t, that’s a safety problem. Call us and we’ll check the setup and document what we find.
Usually yes. Those 1970s-90s wrought-iron and aluminum perimeter styles are common in Whitney’s tract neighborhoods, and we fabricate and weld to match the existing stile and bracket rather than swap the gate.
Bring or send a photo and we’ll quote the matching work in writing. Call (844) 797-2809 for a free estimate.
Whatever’s wrong with the gate, we’d rather show you the number on paper than guess at it over the phone. Give us a call at (844) 797-2809 for a free estimate on gate parts and welding in Whitney – a live person answers around the clock, and the written price comes before any work starts.
Written by the team at Vance Gate Repair Summerlin.